-
shuangbihuan
说明： 直流电机双闭环系统，实现转速和电流的反馈，根据给定的不同，电动机转速也会不同(DC motor double closed loop system)
- 2020-06-25 21:12:17下载
- 积分：1
-
三相永磁同步电机矢量控制建模与仿真
本文首先分析了永磁同步电机矢量控制的发展概况，然后从机电能量转换的角度出发，解释三相永磁同步电机的机电能量转换原理，推导拉格朗日运动方程。此外，列写出永磁同步电机在三相静止坐标系和dq坐标系下的数学模型。基于Simulink建立了转速电流双闭环矢量控制系统的仿真模型，通过对仿真结果分析，验证了永磁同步电机矢量控制系统性能的优越性。(This paper first analyzes the development of permanent magnet synchronous motor vector control, and then explains the electromechanical energy conversion principle of three-phase permanent magnet synchronous motor from the perspective of electromechanical energy conversion, and deduce the Lagrange motion equation. In addition, the mathematical model of permanent magnet synchronous motor (PMSM) in three phase stationary coordinate system and dq coordinate system is listed. Based on Simulink, a simulation model of speed and current double closed loop vector control system is established. By analyzing the simulation results, the performance of PMSM vector control system is verified.)
- 2018-03-27 17:09:35下载
- 积分：1
-
_基于射线跟踪模型的3.5 GHz无线传播特性研究
说明： 3.5 GHz 是 5G 网络部署的重要频段，本文结合射线跟踪模型，对 3.5 GHz 的无线传播特性进行了研究，并于 1.8 GHz 进行了对比，提出 5G 网络初期部署的建议(3.5GHz is an important frequency band for 5g network deployment. In this paper, the radio propagation characteristics of 3.5GHz are studied in combination with ray tracing model, and compared with 1.8GHz. Suggestions for initial deployment of 5g network are proposed)
- 2019-12-11 10:08:09下载
- 积分：1
-
系统辨识及其MATLAB仿真
对动态系统辨识理论做了概括性的介绍，包含了常用的非参数系统辨识方法和参数辨识方法，并将神经网络人工智能算法应用到复杂系统参数识别，适用于系统控制、参数识别与数据预测等领域的学习。传统方法与现在智能算法都配有实例，每个代码文件都有详细注释。(This paper gives a general introduction to the dynamic system identification theory, including commonly used non-parametric system identification methods and parameter identification methods, and applies neural network artificial intelligence algorithms to complex system parameter identification, which is suitable for system control, parameter identification and data prediction. Learning in other fields. Both traditional methods and current smart algorithms are equipped with examples, and each code file has detailed comments.)
- 2018-12-18 13:55:29下载
- 积分：1
-
ABAQUS与Python
采用Python脚本语言二次开发ABAQUS的前处理模块创建了一个带孔平板模型，实现了参数化建模。(Parametrical model using Python in Abaqus.)
- 2020-06-30 16:40:01下载
- 积分：1
-
UPFC模型
UPFC模型，模型非常详细和系统，有助于理解潮流控制器(UPFC model, which is very detailed and systematic, helps to understand power flow controllers)
- 2019-04-22 18:56:05下载
- 积分：1
-
FEM_T3_CST
说明： Matlab 有限元的分析全过程 ，包括前期建模，后处理(Matlab finite element analysis of the whole process, including pre modeling, post-processing)
- 2021-01-05 14:30:46下载
- 积分：1
-
ACO-OFDM
ACO OFDM modulation for VLC system
- 2021-01-23 22:08:45下载
- 积分：1
-
第十次作业
说明： 一受均匀拉力的板，中心带贯穿裂纹，裂纹长2a，使用4节点单元计算裂尖应力分布和应力强度因子(A uniform tensile plate with a through crack in the center and a crack length of 2a is used to calculate the stress distribution and stress intensity factor at the crack tip using a four node element)
- 2020-03-04 18:02:13下载
- 积分：1
-
文件
说明： 混响器的MATLAB实现：利用MATLAB/SIMULINK软件实现混响器(Realization of reverberator with MATLAB)
- 2020-03-25 17:42:37下载
- 积分：1
