登录
首页 » matlab » LMS

LMS

于 2009-09-21 发布 文件大小:221KB
0 126
下载积分: 1 下载次数: 63

代码说明:

  基于LMS和RLS的自适应滤波仿真与分析,内含详细说明(Based on LMS and RLS adaptive filtering simulation and analysis, containing detailed description of)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论


0 个回复

  • monituihuo
    说明:  用模拟退火的算法解决中国旅行商的问题,结果画出图形直观明了!(Using simulated annealing algorithm to solve traveling salesman problem of China, resulting in intuitive and clear graphics to draw!)
    2009-08-11 16:58:56下载
    积分:1
  • parameter_Jakes
    确定离散多普勒频移(fi,n)、多普勒系数(Ci,n)、多普勒相移(@i,n):适用于仿真经典功率谱的情况。(failed to translate)
    2011-05-22 11:05:25下载
    积分:1
  • gaosixiaoqufa
    用matlab高斯消元法求解方程组,主程序里输入矩阵即可(Solving equations with matlab Gaussian elimination, the main program can input matrix)
    2013-03-25 21:19:56下载
    积分:1
  • jc
    说明:  蚁群算法解旅行商问题的MATLAB源码, 城市坐标可自行修改。(Ant Colony Algorithm for Traveling Salesman Problem Solutions MATLAB source code, city coordinates are free to modify.)
    2007-08-07 21:37:24下载
    积分:1
  • ldanew
    LDA source code done with matlab
    2012-06-29 20:34:21下载
    积分:1
  • UWBBPSK
    这个文档采用BPSK超宽带系统。接收器是一个相关接收机具有集成低通滤波器和比较器的门限的选择(This m file models an UWB system using BPSK. The receiver is a correlation receiver with a LPF integrator and comparators for threshhold selection)
    2014-08-08 17:13:13下载
    积分:1
  • 2-Control
    For example, heating up the temperature in a room is a process that has the specific, desired outcome to reach and maintain a defined temperature (e.g. 20°C), kept constant over time. Here, the temperature is the controlled variable. At the same time, it is the input variable since it is measured by a thermometer and used to decide whether to heat or not to heat. The desired temperature (20°C) is the setpoint. The state of the heater (e.g. the setting of the valve allowing hot water to flow through it) is called the manipulated variable since it is subject to control action
    2013-08-16 16:53:45下载
    积分:1
  • AM_Sdq_SVPWM
    三电平SVPWM算法,用于交流传动系统中。(Three-level SVPWM algorithm,Used in ac drive system)
    2014-12-24 16:50:26下载
    积分:1
  • main_no_offset_2
    假设截获了一段短波数字通信的信号,要求解调出最终的信息,每组解调出来后,将10组信息组合起来,恢复最终的信源输出数据。 先验信息:两组数据文件,编号为1、2,每组I、Q两路存放,格式为“int16”,采样率为9600Sa/s,其中第一组为单径情况,第二组为多径情况。 参数符合MIL-STD-188-110A标准; 同步序列为syn=seq.dat,BPSK调制; 接收机频率稳定度高于1e-6。 文件中有效信息总长度为333.75s,其中同步头长为5/12s,每时隙1/6s,训练序列占10 ,在数据之前; 交织方式为全交织,矩阵交织,列为1000,在比特级进行; 纠错码码率为1/2; 调制方式为BPSK、QPSK和8PSK中的一种,映射方式为二进制,BPSK相位偏移为0,其余两种为 。 (Suppose intercepted signal for a period of short-wave digital communications requires final demodulated information after each demodulated, combining 10 group information, to restore the final output data source. Priori information: two sets of data file, numbered 1, 2, each I, Q two-way storage, the format is int16 , sampling rate 9600Sa/s, where the first group is a single path, the second group multipath situation. Parameters meet MIL-STD-188-110A standard Synchronization sequence syn = seq.dat, BPSK modulation The frequency stability of the receiver is higher than 1e-6. File payload total length of 333.75s, wherein the synchronization header length is 5/12s, each time slot 1/6s, accounting for 10 of the training sequence, before the data Interleaving for the whole interleaving matrix interleaving, as 1000, carried out at the bit level Error correction code rate of 1/2 The modulation scheme is BPSK, QPSK and 8PSK one, a binary mapping, the BPSK phase offset is 0, the )
    2016-06-20 19:12:40下载
    积分:1
  • emd
    用于希尔伯特变换,里面有HHT谱计算程序,不是rilling版本,用改进的Hilbert变换,效果好一些,供大家参考(HHT spectrum of the calculation procedures, rilling is not a version of the Hilbert transform used to improve the results better for your reference.)
    2009-06-03 21:49:44下载
    积分:1
  • 696518资源总数
  • 104764会员总数
  • 29今日下载