登录
首页 » matlab » seytem

seytem

于 2010-12-09 发布 文件大小:2910KB
0 181
下载积分: 1 下载次数: 2

代码说明:

  数字pid控制方法及分类的一些M文件 如增强式pid控制算法(Digital pid control method and the classification of some M files Such as increased type pid control algorithm)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • SAX2DTM2
    Iterator that returns all immediate children of a given node.
    2014-01-17 14:24:13下载
    积分:1
  • matlab
    自适应的最小均方算法:只要自适应线性组合器每次迭代运算时都知道输入信号和参考响应,选用LMS算法很合适。(Adaptive least mean square (LMS) algorithm: as long as the adaptive linear combiner for each iteration when they know that the input signal and reference response, selection of LMS algorithm is very appropriate.)
    2009-11-14 09:32:11下载
    积分:1
  • inverposi
    help for possiton analysis of robot
    2010-11-09 18:07:17下载
    积分:1
  • SmartANTENNA
    智能天线程序,关于天线的方向图,和方向因子,增益等仿真(Smart antenna program on the antenna pattern, and direction factor, gain, etc. Simulation)
    2013-08-16 01:41:35下载
    积分:1
  • MC
    FSO通信MC仿真,基于FSO信道特性给出信道损失的Monte Carlo仿真(simulation of FSO Monte Carlo)
    2013-07-20 19:43:51下载
    积分:1
  • gps
    Simulation of GPS in Matlab.
    2012-08-14 18:33:36下载
    积分:1
  • bayes
    bayesian classifier, naive bayesian classifier algorithms are implementer using matlab 2011
    2012-06-29 21:43:25下载
    积分:1
  • code
    A code to code your code.
    2015-04-02 23:32:54下载
    积分:1
  • 802.11a-baseband_2
    IEEE 802.11a-1999 or 802.11a was an amendment to the IEEE 802.11 wireless local network specifications that defined requirements for an orthogonal frequency division multiplexing (OFDM) communication system. It was originally designed to support wireless communication in the unlicensed national information infrastructure (U-NII) bands (in the 5–6 GHz frequency range) as regulated in the United States by the Code of Federal Regulations, Title 47, Section 15.407.
    2014-02-01 23:29:12下载
    积分:1
  • 用Z-N法实现P,PI,PID控制的参数整定
    用MATLAB程序软件完成Z-N法对控制器的参数整定,实现P,PI,PID控制器的分别参数整定,并求出控制器的控制参数Kp,Ti,Td。最后绘制出不同控制器控制下的及参数整定前后的单位阶跃响应图进行比较。(MATLAB program software is used to complete the parameter tuning of the controller by Z-N method. The parameters of P, PI, PID controller are adjusted, and the control parameters of the controller Kp, Ti, Td are obtained. Finally, the unit step response diagram before and after parameter tuning is plotted under different controller control.)
    2021-03-18 10:49:20下载
    积分:1
  • 696518资源总数
  • 106265会员总数
  • 10今日下载