-
signal-and-system
说明： 这是基于matlab下的数字信号处理示例，包括信号、系统和系统响应的实现等(These are some digtal signal processing examples based on the matlab. And these include filter ,matrax algthrom,and so on......)
- 2011-03-31 00:12:18下载
- 积分：1
-
CIAYANG
说明： 根据采样定理编写程序,实现模拟信号的采样,画出采样波形.(According to sampling theorem, programming, analog signal sampling, draw sample waveform.)
- 2010-05-03 13:33:45下载
- 积分：1
-
communication-simulation-code
matlab通信工程仿真的代码，各章的代码都有，使用matlab编译的，都已经通过验证，运行，希望对你有点帮助！(matlab communication engineering simulation code, each chapter code, using matlab compiled, have validated run, you want a little help!)
- 2013-02-28 14:43:50下载
- 积分：1
-
demomodel
This demo explains the use of the advanced object oriented interface model. The model is the generic object which collects all relevant signals, parameters, options and functions related to an application of the LS-SVM. This interface is depreciated for the casional users because of the implicit nature: the distinction between in- and output vanishes. If one wants to use the full power of LS-SVMlab, one is recommended to go through this demo. The options can be divided in 5 classes, the general LS-SVM options the trainpoint administration, the options of the Conjugate Gradient algorithm the preprocess options and the encoding options. The demo shows how to control the preprocessing and the coding using the appropriate model. It is adviced to check carefully the model s options before starting the calculations.
- 2015-01-18 05:52:05下载
- 积分：1
-
Boost_Converter
说明： 升压转换器是一种DC / DC电源转换器，可将电压从其输入（源）升至其输出（负载）。在连续导通模式下（流经电感的电流永远不会降为零），升压转换器的理论传递函数为：
占空比在哪里0.5
在此示例中，转换器从250 V电源馈送RC负载，并且PWM频率设置为31 kHz。
模拟
运行仿真并观察示波器上的波形。确认负载电压（Vout）的平均值非常接近理论值：Vout = 250 /（1- 0.5）= 500V。(A boost converter is a DC/DC power converter which steps up voltage from its input (source) to its output (load). In continuous conduction mode (current through the inductor never falls to zero), the theoretical transfer function of the boost converter is:
where is the duty cycle.0.5
In this example, the converter is feeding an RC load from a 250 V source and the PWM frequency is set to 31 kHz.
Simulation
Run the simulation and observe waveforms on Scope. Verify that the mean value of the load voltage (Vout) is very close to the theoretical value of: Vout = 250 / (1 - 0.5) = 500 V.)
- 2020-03-22 20:41:56下载
- 积分：1
-
array-factor
this document consists of the code to find the linear array radiation pattern
- 2011-01-23 01:54:54下载
- 积分：1
-
Beginners_code_CS
非常适合压缩感知-compressed sensing初学者学习的入门matlab代码。(Beginners Code for Compressive Sensing。)
- 2014-12-22 21:20:35下载
- 积分：1
-
CPSIR
仿真程序，模拟SIR信息传播模型的CP过程。SIR模型是基于传染病动力学的信息传播模型。(The simulation program, CP SIR information dissemination process simulation model. SIR model is a model for the dissemination of information on the dynamics of infectious diseases.)
- 2014-05-11 21:30:39下载
- 积分：1
-
harmonic_analysis_of_one_month_data
潮汐调和分析 利用t-tide程序对实测数据资料进行的潮位调和分析 求出调和常数(Tidal harmonic analysis procedure using t-tide data for the measured harmonic analysis of tidal harmonic constants obtained)
- 2020-06-29 23:40:02下载
- 积分：1
-
csc_v
说明： CSC变换，simulink仿真，包含MATLAB仿真文件验证(CSC transform, simulink simulation, including the MATLAB simulation file validation)
- 2009-08-07 19:42:21下载
- 积分：1
