登录
首页 » matlab » siscod

siscod

于 2010-05-25 发布 文件大小:71KB
0 110
下载积分: 1 下载次数: 9

代码说明:

  LS and MMSE comparaison

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论


0 个回复

  • reprojection
    基于块投影的图像恢复算法,matlab程序(denoise)
    2010-12-09 01:26:45下载
    积分:1
  • programs
    MATLAB PROGRAMS MATLAB PROGRAMS MATLAB PROGRAMS
    2013-07-27 02:45:32下载
    积分:1
  • Figure-in-matlab
    用MatLab做卫星绕地运行的复杂图像,在图像当中可以(A interpretation of making figure in matlab:simulate the moving of satelite around earth)
    2014-11-01 14:33:21下载
    积分:1
  • Weight-InletV-PIDprocess-simulation
    编写了基于matlab的PID仿真程序模拟水泥行业稳料仓重流程。 稳料仓仓重Weight为CV,入口阀门InletV为MV,出口阀门OutletV为DV,搭建闭环流程仿真,并进行测试。(The preparation of a PID matlab simulation program to simulate the steady bin heavy flow based on cement industry. Stable storage bin weight Weight for CV, InletV for the MV entrance valve, outlet valve of OutletV DV, to build closed-loop process simulation, and test.)
    2015-02-04 14:06:04下载
    积分:1
  • Cross-Correlation
    Cross Correlation function implemented in matlab
    2013-05-14 12:59:20下载
    积分:1
  • JAC-blackman
    JAC—blackman 算法历程,通过这个算法可以对正弦信号频率进行精细估计(Quinn algorithm course, you can fine sinusoidal signal frequency estimation by this algorithm)
    2016-01-08 20:30:53下载
    积分:1
  • shuzhifenxiMATLABI
    说明:  这是有关数值分析的MATLAB练习册程序,学习人员可以参考一下(This is a MATLAB workbook program for numerical analysis, which can be consulted by learners.)
    2019-03-02 20:39:01下载
    积分:1
  • ofdm-emluator
    信道编码采用卷积码,解码使用Viterbi解码。调制给出QPSK、16QAM 两种调制方式,并在AWGN和瑞利信道两种信道模型下传输。(Channel coding using convolutional codes, decoding using the Viterbi decoder. Given modulation QPSK, 16QAM modulation in two ways, and in the AWGN and Rayleigh channel model of two-channel transmission.)
    2020-12-12 19:59:16下载
    积分:1
  • pcm_quan_enco
    file Matlab abc xyz a b c d e f x y z d h i k l m n s
    2012-03-30 10:27:20下载
    积分:1
  • regular_mesh
    Finland Matlab cannot do regular meshes for non-regtancular regions. However, one can manually do very coarse regular meshes for these type domains. The difficulty is with the edge data e. If this data does not correspond to the orientations given by the PDEtool geometry files, refinement will not work. The function drawedges() will display the order of the edges and their segment numbers. However, this function does not tell how the edges are oriented. However, just run the visualization, and if the refinement does not work correctly, you know the problem is with the orientatino of the edge. Remember to also correct the last two rows of the matrix e when changing the orientation. (See the documentation for initmesh for more info.)
    2015-01-21 09:22:16下载
    积分:1
  • 696518资源总数
  • 104716会员总数
  • 28今日下载