登录
首页 » SCM » cs8900A的详细资料,详细介绍了开发CS8900A的流程,很具有指导意义...

cs8900A的详细资料,详细介绍了开发CS8900A的流程,很具有指导意义...

于 2023-03-17 发布 文件大小:1.38 MB
0 40
下载积分: 2 下载次数: 1

代码说明:

cs8900A的详细资料,详细介绍了开发CS8900A的流程,很具有指导意义-CS8900A detailed information on the development of a detailed introduction of the CS8900A flow, it is instructive

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 定时器计数器语言程序设计,在中央部分是不可缺少的…
    定时计数器的c语言编程,这是在单片机编程不可缺少中央部分。-Timer counter c language programming, which is indispensable in the central part of microcontroller programming.
    2022-07-18 05:56:53下载
    积分:1
  • 自己做的一个单片机实验,实现led灯的闪烁
    自己做的一个单片机实验,实现led灯的闪烁-Their own to do a single-chip experiment, led lights flicker realize
    2022-03-13 11:15:33下载
    积分:1
  • Short Message gsm alarm procedures, and hardware with complete switch input, sho...
    gsm短消息报警程序,与硬件配合,完成开关量输入,短消息通知主人,用于防盗报警系统。-Short Message gsm alarm procedures, and hardware with complete switch input, short message to inform the owner for the anti-theft alarm system.
    2022-04-18 14:41:47下载
    积分:1
  • 凌阳单片机的语音程序4,供学习凌阳单片机的学习者参考
    凌阳单片机的语音程序4,供学习凌阳单片机的学习者参考-Sunplus SCM four voice procedures for learning Sunplus SCM reference learners
    2023-03-08 02:40:03下载
    积分:1
  • protues仿真!单片机仿真的源代码
    protues仿真!单片机仿真的源代码-protues
    2022-04-18 04:30:20下载
    积分:1
  • Advantages: only a small interruption in the things I usually post in the receiv...
    优点:中断中只做很少的事情,通常我是在接收中断中post一个信号量,触发别的任务读数据-Advantages: only a small interruption in the things I usually post in the receiving a signal interruption in the amount of time to trigger other mission data
    2023-05-16 16:05:03下载
    积分:1
  • 三相步进电机的三相六拍工作方式,正转的绕组通电顺序:A、AB、B、BC、C、CA、A,反转的通电顺序:A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性,故步进电机的工作过程中不能及时的启动和停止,在启动时应慢慢的加速到预定速度,在停止前应逐渐减速到停止,否则,将产生失步现象。 步进电机的控制问题可总结为两点: 1、产生工作方式需要的时序脉冲; 2、控制步进电机的速度,使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.
    2022-07-20 15:21:46下载
    积分:1
  • 用凌阳16位单片机测试输入波形的频率,动态刷新显示
    用凌阳16位单片机测试输入波形的频率,动态刷新显示-Sunplus 16-bit single-chip microcomputer used to test the frequency of input waveform, dynamic refresh display
    2023-05-17 07:25:03下载
    积分:1
  • msp430I2C通信读AT24C02,编译通过
    msp430I2C通信读AT24C02,编译通过-Reading msp430I2C communications AT24C02, compiled through
    2022-01-25 17:31:33下载
    积分:1
  • msp430f2系列的资料,适合初学者,希望大家下载学习
    msp430f2系列的资料,适合初学者,希望大家下载学习-msp430f2 series of information, suitable for beginners, I hope everyone downloads Learning
    2022-10-19 05:15:05下载
    积分:1
  • 696521资源总数
  • 104072会员总数
  • 37今日下载