TX-1开发板的Proteus仿真（大部分功能）-TX-1 development board of the Proteus simulation (most features)

关于16行64列的LED点阵，能够左右移动，程序简单易懂，希望大家来下载-16, line 64 on the LED dot-matrix, can move around, the program easy-to-read, I hope everyone to download

用Keil uVision2编写得批量in传输程序，实现简单得数据采集，我看了觉得很有用-with Keil uVision2 prepared in bulk in transmission process, in simple data collection, I saw very useful

急救车与交通灯）（1）南北与东西方向，每个方面由红黄绿三个灯控制（2）南北向：　红（30秒），黄（5秒），绿（25秒）　　　东西向： 红（35秒），黄（5秒），绿（25秒）　　　上述基本参数可以根据实际情况自行调整，灯的变化规律与实际路口规律相同，绿灯在最后5秒钟时，黄灯亮，然后红灯亮，不允许两个方面同时亮绿灯。（3）绿灯的时间显示在数码管上进行显示。（4）可以通过一个开关控制，当开关信号为0时，整个交通灯全灭提高要求：（1）设计一个紧急控制开关信号，当紧急开关信号为1时，两个方向的灯全为红灯。紧急开关撤消后，按照开关按下之前的状态继续运行（其参数要保存）。（2）设计一个夜间行车开关，当开关按下后，两个方向都只有黄灯闪烁，其它灯熄灭。（3）设计两个方向的亮时时间可调。-emergency vehicles and traffic lights) (1) North and South and east-west direction, each with three yellow-green from red lights control (2) to the north and south : red (30 seconds), yellow (5 seconds), Green (25 seconds) to things : red (35 seconds), yellow (5 seconds) Green (25 seconds) above basic parameters can be adjusted to the actual situation, the light changes with the actual law of the same intersection, the green light in the final five seconds, the yellow light is on, and then a red light, bright, not two fronts simultaneously bright green. (3) the green light at the time displayed on the digital display control. (4) can be controlled by a

自己写的用AVR 单片机产生正弦波.用示波器观察波形很好！-Write your own single-chip generated sine wave with AVR. Oscilloscope to observe waveforms with very good!

触摸屏的校正程序。可以用于触摸屏的校正。在三星的平台上测试通过-Touch screen calibration procedure. Can be used for touch-screen calibration. Samsung

LCD-7279的经过调试多次已经能够实现在指定的位置显示特定的数据。 程序lcd1.c实现基本的功能，即：键盘输入0、1、2、3、4、5、6、7、8、9、acdef 在液晶的指定位置显示实现满屏或半屏显示点阵和字符，调入一幅图画的代码进行显示；-LCD-7279 after the repeated testing has been able to achieve the specified location-specific data. Lcd1.c procedures to achieve the basic functions, namely : the keyboard input 0, ,36.2. 8,9. a b c d e f in the designated location LCD realize Manping or semi-Screen Display and characters, transferred to a picture of the code display;

LPC单片机读写EEPROM程序-LPC SCM reader EEPROM process

基于单片机的无线遥控系统，这是本人精心制作的课程设计，花了将近一个月的时间才完成的。里边有具体的程序代码，全都是仿真通过，并且做出了pcb板，经得起考验的-Based on single-chip wireless remote control system, This is my elaborate curriculum design, has spent nearly a month before the finish. Inside there is a specific code, all the simulation are passed, and made a pcb board, stand the test of

PIC单片机C语言学习－教程-PIC C language learning-Guide