-
TLC5615 DA转换器驱动程序（KEIL）
TLC5615 DA转换器驱动程序（KEIL）-TLC5615 DA converter Driver (KEIL)
- 2022-03-17 05:59:46下载
- 积分：1
-
Singlechip p87lpc76x procedures
p87lpc76x单片机程序-Singlechip p87lpc76x procedures
- 2022-03-06 19:42:56下载
- 积分：1
-
A complete STC89LE5412 procedures, to achieve 2
一个完整的STC89LE5412程序，实现２路电压，２路电流采样，滤波，和瞬间功率峰值计算-A complete STC89LE5412 procedures, to achieve 2-way voltage, 2-way current sampling, filtering, and calculation of instantaneous peak power
- 2022-01-25 20:26:38下载
- 积分：1
-
单片机外部中断
串口中断 定时中断 单片机外部中断
串口中断 定时中断...
单片机外部中断
串口中断 定时中断 单片机外部中断
串口中断 定时中断 -micro conctol micro conctol micro conctol micro conctol
- 2022-04-30 21:13:51下载
- 积分：1
-
红外解码程序，该程序可为用户提供正确的解码方案，但前提是理解好每个红外的发送过程...
红外解码程序，该程序可为用户提供正确的解码方案，但前提是理解好每个红外的发送过程-IR decoding process, which can provide users with the correct decoding, but the premise is a good understanding of the sending process for each infrared
- 2022-02-02 21:15:31下载
- 积分：1
-
该文件包括利用MPS4300控制LED控制芯片TLC5941硬件和C代码,该方案是用于流行的LED背光源....
该文件包括利用MPS4300控制LED控制芯片TLC5941硬件和C代码,该方案是用于流行的LED背光源.-The document including the use of LED control chips MPS4300 control TLC5941 hardware and C code, the program is used to pop the LED backlight.
- 2022-12-15 17:15:03下载
- 积分：1
-
八路电压表C程序
使用AT89C52单片机，12MHZ晶振，P0口读入AD值，P2口作AD控制，用共阳LED数码管
P1口输出段码，P3口扫描，最高位指...
八路电压表C程序
使用AT89C52单片机，12MHZ晶振，P0口读入AD值，P2口作AD控制，用共阳LED数码管
P1口输出段码，P3口扫描，最高位指示通道（0-7）。-Eight-way voltage meter C program using AT89C52 single-chip, 12MHZ crystal, P0 I read into the AD value, P2 I make AD control, with a total of P1 Yang LED digital tube output above code, P3 port scan, the maximum channel bit instructions (0-7).
- 2022-01-31 16:25:46下载
- 积分：1
-
C51编写的IC卡读写程序
C51编写的IC卡读写程序-C51 prepared by the IC card reader procedures
- 2022-08-15 05:32:01下载
- 积分：1
-
keil C51 ISR事例
keil C51 ISR事例-ISR stories
- 2022-03-31 19:22:35下载
- 积分：1
-
由8051组成的单片机系统通常情况下，P0口分时复用作为地址、数据总线，P2口提供A15...
由8051组成的单片机系统通常情况下，P0口分时复用作为地址、数据总线，P2口提供A15-A8即高8位地址，P3口用作第二功能，只有P1口通常用作I/0口。P1口是8位准双向口，它的每一位都可独立地定义为输入或输出，因此既可作为8位的并行I/O口，也可作为8位的输入输出端。当工作在输入方式时，对应位的锁存器必须先置1,才能正确地读到引脚上的信号,否则,执行读引脚指令时,若对应位的锁存器的值为0，读的结果永远为0。-By 8051, composed of single-chip microcomputer system under normal circumstances, P0 timeshare I reuse as address, data bus, P2 I provide A15-A8 high eight address, P3 mouth for the second function, I usually only P1 for I/0 I. P1 I was eight quasi-two-way port, it can be independent of each and every defined as input or output, it can be used as 8-bit parallel I/O port, can also be used as 8-bit input and output side. When the work in the input, the corresponding bit latch must first buy one in order to correctly read the signal pin, or pin the implementation of reading instruction, if the corresponding bit latch the value of 0, Reading the results of Forever to 0.
- 2023-08-10 04:55:03下载
- 积分：1
