-
在AVR单片机下通过USART实现串口通讯，里面包含有其配置及源码。...
在AVR单片机下通过USART实现串口通讯，里面包含有其配置及源码。-In the AVR microcontroller achieved through USART serial communication, which contains its configuration and source code.
- 2022-01-25 23:09:11下载
- 积分：1
-
AD 转换
用定时器中断 显示
0
AD 转换
用定时器中断 显示
0--5V-AD0804
zhongduan xianshi
- 2022-01-25 19:06:06下载
- 积分：1
-
用AT89S51单片机制作的一个带通讯的数字电压表，内含电路原理图及汇编源程序代码，以及数张图片，还有论文和设计感想。倾力奉送！...
用AT89S51单片机制作的一个带通讯的数字电压表，内含电路原理图及汇编源程序代码，以及数张图片，还有论文和设计感想。倾力奉送！-AT89S51 produced using a single-chip communications with digital voltage meter, including the circuit schematic and the compilation of source code, as well as a few pictures, there are papers and design thoughts. Effort away!
- 2023-05-02 13:20:04下载
- 积分：1
-
DS18B20.C(一般通用的数字温度传感器)完成代码,可直接使用.
DS18B20.C(一般通用的数字温度传感器)完成代码,可直接使用.-DS18B20.C (general use digital temperature sensor) the completion code can be used directly.
- 2022-07-07 02:48:57下载
- 积分：1
-
这是LCD1602与msp430之间的通信,其实可以直接从51移植过来,但是一定要在硬件加上拉电阻,要不然是不通不过的,我说的是你用的是5V的LCD...
这是LCD1602与msp430之间的通信,其实可以直接从51移植过来,但是一定要在硬件加上拉电阻,要不然是不通不过的,我说的是你用的是5V的LCD-This is the LCD1602 and communication between the MSP430 can in fact be a direct transplant from the 51, but must be coupled with pull-up resistor in the hardware, otherwise it is unreasonable, however, I say is that you use the LCD is 5V
- 2022-02-15 05:17:19下载
- 积分：1
-
J1939协议的源代码，支持PIC18F单片机。有一个详细的说明文件…
J1939源代码，支持PIC18F系列单片机。有详细的说明文档，移植方便。-J1939 source code, support PIC18F MCU. Have a detailed description of the document, to facilitate transplantation.
- 2022-04-14 11:00:30下载
- 积分：1
-
on DDSAD9850 plans and procedures for the control procedures Serial MCU ADUC812
关于DDSＡＤ９８５０图和程序串口程序主控单片机ＡＤＵＣ８１２-on DDSAD9850 plans and procedures for the control procedures Serial MCU ADUC812
- 2022-07-15 03:36:51下载
- 积分：1
-
C51 for the Modbus protocol, the tests will be run, but still not perfect
用于C51上的modbus协议，经测试可运行，但还不完善-C51 for the Modbus protocol, the tests will be run, but still not perfect
- 2022-08-21 05:31:55下载
- 积分：1
-
注:protel电路图
1.INPUT12为高压气压和低压压传感器输入端.
2.OUTPUT为充气输出控制端.
3.当高低压有接地信号时,电机...
注:protel电路图
1.INPUT12为高压气压和低压压传感器输入端.
2.OUTPUT为充气输出控制端.
3.当高低压有接地信号时,电机正转,气阀打开.
4.INPUT2低气压时有信号时,充气OUTPUT输出,充气电机转.
5.RS1与RS2是调节阀门距离用地
6.RS3是与气阀电机同步时,是气阀电机的转动圈数传感器.
7.RS4是调节延时时间用地-Note: protel circuit 1.INPUT12 and low-voltage high-pressure pneumatic pressure sensor input. 2.OUTPUT output control for the inflated side. 3. When the high and low pressure have a grounding signal when the motor is transferred, the valve opens. 4.INPUT2 low pressure when there is signal output OUTPUT inflatable, inflatable motor switch. 5.RS1 and RS2 is the regulator valve from the land 6.RS3 synchronous motor with the valve, the valve motor is rotating circle the number of sensors. 7.RS4 delay time to regulate land
- 2022-02-05 21:01:24下载
- 积分：1
-
51单片机C语言编程手册，由周立功发布，详细介绍了51的硬件与C编程...
51单片机C语言编程手册，由周立功发布，详细介绍了51的硬件与C编程-51 Single-chip C language programming manual, by the week Ligong released details of 51 hardware and C programming
- 2022-02-26 18:30:21下载
- 积分：1
