-
counter
设计一个十进制计数器模块，输入端口包括 reset、up_enable 和 clk，输出端口为 count
和 bcd，当 reset 有效时（低电平），bcd 和 count 输出清零，当 up_enable 有效时（高电
平），计数模块开始计数（clk 脉冲数），bcd 为计数输出，当计数为 9 时，count 输出一
个脉冲（一个 clk周期的高电平，时间上与“bcd=9”时对齐）(Design of a decimal counter module, input port, including the reset up_enable clk, output port for the count and bcd, when reset is active (low), the bcd and count output cleared up_enable active (high), count module starts counting the (the CLK pulse number), the BCD count output when the count 9, the count output of the high level, the time of a pulse (a clk cycle with " bcd = 9" when aligned))
- 2013-04-13 19:53:29下载
- 积分：1
-
daima
Rst是低电平有效的系统复位信号，Clk是时钟信号。AB[5：0]是地址信号，DB[7：0]是数据信号，wr是低电平有效的写信号。start是启动信号。
模块中有一个64x8的双端口的存储器。系统复位结束后，可以通过AB、DB和wr信号向同步存储器写入数据。当写入64个数据后，给出一个Clk周期宽度的脉冲信号start，则系统从存储器0地址处开始读出数据，读出的8位数据从低位开始以3位为一组，每个时钟周期输出一组，即第一个时钟周期输出[2：0]位，第二个时钟周期输出[5：3]位，第三个周期输出1地址的[0]位和0地址的[7：6]位，直至将存储器中64x8数据全部输出。若最后一组不足三位，则高位补0。
(Rst is an active-low system reset signal, Clk is a clock signal. AB [5: 0] is the address signal, DB [7: 0] is the data signal, wr write signal is active low. start is the start signal. Module in a dual port memory of 64x8. After the reset, you can write data to the synchronous memory by AB, DB and wr signals. When data is written to 64, given the width of a pulse signal Clk cycle start, the system begins to read the memory address 0, 8 data read out a low starting with three as a group, each clock outputs a set period, which is the first clock cycle of the output [2: 0] bits, the second clock cycle output [5: 3] position, the third cycle of the output of an address [0] and 0 address [7 : 6] bit, until all the data in memory 64x8 output. If the last group of less than three, the high 0s.)
- 2014-12-11 20:16:04下载
- 积分：1
-
lacp
lacp代码，可以参照学习Lacp协议的相关状态机等知识(LACP code, can refer to the relevant state machine learning knowledge of Lacp protocol)
- 2014-12-09 17:14:11下载
- 积分：1
-
bignum
a big number class and a calculator using the class
- 2012-12-25 10:14:31下载
- 积分：1
-
基于fpga的DDS程序 AD9767
基于fpga的DDS程序 可输出正弦波 方波 三角波 锯齿波(DDS program based on FPGA can output sinusoidal square wave triangular wave sawtooth wave)
- 2020-06-20 21:00:01下载
- 积分：1
-
lesson38_lcd1602_clander
说明： 基于Verilog语言编写的LCD1602显示的日历程序，类似时钟功能值得参考。(LCD1602 shows calendar program based on Verilog language, similar clock function is worth reference.)
- 2019-05-26 09:29:18下载
- 积分：1
-
05_fifo_test
说明： FIFO: First in, First out 代表先进的数据先出，后进的数据后出。Xilinx 在 VIVADO 里为我们已经提供了 FIFO 的 IP 核, 我们只需通过 IP 核例化一个 FIFO，根据 FIFO 的读写时序来写入和读取FIFO 中存储的数据。(FIFO: first in, first out represents the first out of advanced data, and the last in data is the last out. Xilinx has provided us with the IP core of FIFO in vivado. We only need to instantiate a FIFO through the IP core, and write and read the data stored in FIFO according to the FIFO read-write timing.)
- 2021-04-08 22:19:20下载
- 积分：1
-
16_QAM
用verilog 语言编译16QAM调制(a great complied code of 16QAM modulation for OFDM)
- 2013-09-02 16:23:40下载
- 积分：1
-
Implementing a TMDS Video Interface in the Spartan-6 FPGA
This application note describes a set of reference designs able to
transmit and receive DVI and HDMI data streams up to 1080 Mb/s using the
native TMDS I/O interface featured by Spartan-6 FPGAs.
- 2022-10-21 19:25:03下载
- 积分：1
-
14_SDRAM
高速流水的SDRAM控制器，最高速度可达速度在200M左右(high speed SDRAM controller)
- 2019-06-17 18:43:54下载
- 积分：1
