-
quxianbiaojiyuzuobiao
利用matlab程序编写可以实现找到曲线标记的方法以及可以指定坐标轴范围的程序。(Matlab programmers can use to find curves labeled realize Ways and axes can specify the scope of procedures.)
- 2009-02-19 18:22:27下载
- 积分:1
-
ahastar-r2008-07-31.tar
robot planning path in 3D
- 2009-11-07 00:50:38下载
- 积分:1
-
demo
8自由度的汽车模型,包括abs clutch 建立了动力学公式的模型,需要对几个积分器设置初值,避免代数环(vehicle model of 8 degrees)
- 2010-12-22 19:57:29下载
- 积分:1
-
stepcontrol
说明: MATLAB编写的仿真小程序,关于STEP CONCROL的,仿真出CONTROL执行后的图形(MATLAB simulation prepared by the small program on STEP CONCROL. Simulation out CONTROL implementation of the graphics)
- 2006-02-06 09:03:12下载
- 积分:1
-
xiangguanxishu
能对两个信号进行相关性分析,在进行分析时,注意不同的方法可能意义不太一样(Correlation analysis can be performed on the two signals)
- 2014-12-25 08:09:48下载
- 积分:1
-
聚类-k均值算法
说明: K-means算法是基于划分的思想,因此算法易于理解且实现方法简单易行,但需要人工选择初始的聚类数目即算法是带参数的。类的数目确定往往非常复杂和具有不确定性,因此需要专业的知识和行业经验才能较好的确定。而且因为初始聚类中心的选择是随机的,因此会造成部分初始聚类中心相似或者处于数据边缘,造成算法的迭代次数明显增加,甚至会因为个别数据而造成聚类失败的现象。(K-means algorithm is based on the idea of partitioning, so the algorithm is easy to understand and the implementation method is simple and feasible, but it requires manual selection of the initial number of clusters, that is, the algorithm is with parameters. The number of classes is often very complex and uncertain, so professional knowledge and industry experience are needed to better determine. Moreover, because the selection of initial clustering centers is random, some initial clustering centers will be similar or at the edge of data, resulting in a significant increase in the number of iterations of the algorithm, and even the phenomenon of clustering failure due to individual data.)
- 2020-06-21 17:40:01下载
- 积分:1
-
生成加密密钥共享
生成加密密钥共享
- 2022-12-13 18:05:03下载
- 积分:1
-
无线传感器网络节点定位算法实现Localization
"未知节点可能因为没有邻居锚节点而无法定位"
实现算法可能的方法:
1. 未知节点利用邻居锚节点进行定位,没有邻居锚节点的未知节点无法定位。
2. 未知节点一旦被定位,就充当锚节点。这时没有邻居锚节点的未知节点在等到自己的邻居未知节点定位之后就可以进行定位。
3. 有邻居锚节点的未知节点只利用邻居锚节点进行定位,没有邻居锚节点的未知节点才利用已经定位了的邻居未知节点进行定位。
Centroid.m, Bounding_box.m, Grid_Scan.m,RSSI.m采用的第一种方法;
Centroid_second.m, Bounding_box_second.m, Grid_Scan_second.m,RSSI_second.m采用的第二种方法;
Centroid_third.m, Bounding_box_third.m, Grid_Scan_third.m,RSSI_third.m采用的第三种方法;
DV-hop,MDS-MAP不存在这三种方法的选择。
Centoid, Bounding_box, Grid_Scan, RSSI, DV_hop, MDS_MAP,APIT的执行在run.m中直接选择就可以了;
- 2023-08-16 19:55:05下载
- 积分:1
-
matlab
matlab教程电子版,非常适合初学者,讲得很详细,非常好理解(Very suitable for beginners, very detailed, very good understanding)
- 2014-10-31 22:49:04下载
- 积分:1
-
Matlab06
摘要:计算机动态仿真是混沌应用研究的重要方法"该文介绍了环境下的可视化建模与动态仿真步骤(Abstract: The computer simulation is a chaotic dynamic applied research an important means of )
- 2008-05-16 10:47:53下载
- 积分:1