-
disjw
利用两点距离计算经纬度的matlab程序,欢迎交流。(use latitude and longitude distance calculation procedures of Matlab, welcomed the exchange.)
- 2006-09-23 00:02:11下载
- 积分:1
-
rx_2
BCH,LPDC,walsh编解码源程序代码,在视频传输中应用广泛(BCH ,the LPDC ,walsh codec source code, widely used in video transmission)
- 2013-03-15 20:35:04下载
- 积分:1
-
Compensate
补偿算法,用于传感器非线性补偿,可以参考,大家感兴趣可以下来看下,欢迎下载。(Compensation algorithm for nonlinear compensation sensor, reference, we are interested can look down, welcome to download.)
- 2014-12-09 16:19:39下载
- 积分:1
-
时延和丢包的网络控制系统的补偿控制分析研究 Control-of-Network-System
本文是基于MATLAB的具有时延和丢包的网络控制系统的补偿控制分析研究(Predictive Control of Network Control System w ith Network Delay and Data PacketDropout)
- 2011-12-16 11:41:29下载
- 积分:1
-
predict-and-match-interal-multiple
地震信号处理,虚同相轴方法预测层间多次波,将数据分成上下两部分,利用相关和褶积的原理预测出层间多次波。预测信号和原始信号在相位和振幅上存在差异,用L1范数匹配法进行匹配,其中,提供了两种方法解病态方程,分别为高斯-赛德尔方法和正则化方法。(Seismic signal processing, predicte internal multiples by construct virtual events .The data is divided into two parts, using the principle of correlation and convolution to predicte multiples. There are differences between the prediction signal and the original signal on the phase and amplitude, so we use the L1 norm method to match the singal.We provide two methods for solving ill equation, respectively Gauss- Seidel method and regularization method.)
- 2015-06-11 15:53:04下载
- 积分:1
-
totallyFuzzyMultiItem
totally fuzzy for using at matlab, you can make it better with this function
- 2009-12-14 17:05:59下载
- 积分:1
-
chepaishibia
说明: 对于初学者学习matlab很有帮助,尤其在图像处理方面更是很好的啊。(For beginners learn matlab ® helpful, especially in the image processing is very good.)
- 2010-03-28 20:46:25下载
- 积分:1
-
MasterMATLAB_Polynomial_Interpolation
Matlab的多项式,插值,样条函数 word 版本(MATLAB Polynomial Interpolation And Spline)
- 2009-06-10 23:51:02下载
- 积分:1
-
vscmain
variable structure sliding mode controller
- 2011-01-05 12:02:57下载
- 积分:1
-
GMSK_QPSK_8PSK
说明: 里面有8PSK,GMSK的matlab源程序,贡献出来了(I was interested in the theory for 8PSK and came across this m-file written in 1999. It
requires 2 function calls (graymapPSK and grayunmapPSK) which I have
included and must be uncommented(single comments only) and loaded into your workspace.
Remove the function calls from this m-file after you load into your
workspace.
It seems to work well and give valid results for BPSK and QPSK but I have a question
about the setup for 8PSK and the solution for Pseint where Pse=Pseint.
Also, the Gray coding seems different than what I m used to.
Some of you more theoretical minded may have some insight into the theory
behind how Pseint was determined and comment. I don t have the
communications toolbox-blockset and was wondering how it compared with Matlab s
example simulation of 8PSK with Gray coding (in Simulink?)
Each run takes about a minute and the loop iterations are shown in the
command window.
A numerical example of a satellite link is shown using uncoded QPSK )
- 2009-08-25 19:32:08下载
- 积分:1