登录
首页 » Java » _-5

_-5

于 2012-09-21 发布 文件大小:379KB
0 126
下载积分: 1 下载次数: 2

代码说明:

  MATLAB 编程有助于初学者进行学习,了解以及相应的运用(MATLAB programming will help beginners to learn, understand, and use of appropriate)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • UWB_TX_RX
    uwb receiver and transceiver with matlab
    2009-03-01 17:33:22下载
    积分:1
  • LMS_RLS
    LMS和RLS算法性能的比较,包括权值比较、遗忘因子的影响等(LMS and RLS algorithm performance comparisons, including the right value compared with the impact of forgetting factor)
    2008-04-23 23:59:47下载
    积分:1
  • R14
    IEEE 802.15.3a 多子带OFDM系统物理层仿真链路。基与Matalb R14版本(IEEE 802.15.3a more sub-band OFDM physical layer simulation system link. Matalb R14 version of the base and)
    2009-07-11 10:12:26下载
    积分:1
  • radar-coortarns
    雷达的坐标系相关变换说明文档,介绍了雷达坐标西与大地坐标系的变换关系,参考使用可以编织坐标变换代码(Radar Coordinate Transnate)
    2015-02-10 22:15:05下载
    积分:1
  • kdtree_in_matlab
    kd-tree 是一种常用的数据结构,它在搜索最近点中有普遍用处。该文件是一个用纯matlab写成的源代码。(kd-tree is a commonly used data structure, it is commonly used in searches for the nearest point. The file is a pure source code written in matlab.)
    2010-07-17 15:47:35下载
    积分:1
  • 03
    说明:  03_认识MetaCharacters03_认识MetaCharacters03_认识MetaCharacters(RegExp)
    2009-12-20 17:50:01下载
    积分:1
  • C-C-Method
    采用C-C法的同时求时延与嵌入维的经典程序(CC method using delay and embedding dimension while seeking the procedure)
    2013-10-17 20:03:10下载
    积分:1
  • chengxu
    小波变换进行变速箱故障诊断 首先将s1和s2信号时域谱(s1代表维修前的振动信号,s2代表维修后的振动信号),画出来进行对比,会发现s1信号的振动幅值会比较高;然后对s1和s2分别进行小波分解并画出各层的时域谱,只对比s1和s2分后的最高时域谱,s2更加的具有周期性,且幅值较小,s2周期性不够明显,且振动过于密集。分析完时域谱后开始分析频谱,首先对原信号s1和s2fft转换,得到频谱图,如图,然后再对小波分析后高频部分进行fft转换,做出频谱图。对比后我们发现,在f 2375HZ出(也就是齿轮的啮合频率),s1信号频谱幅值会有急剧的升高,然后,其谐波的幅值也会增大。所以可以推断出该维修前的增速箱的齿轮可能出现问题。(Gearbox fault diagnosis based on wavelet transform s1 and s2 first time domain signal spectrum (s1 behalf of the vibration signal before maintenance, vibration signal s2 representative of repaired), drawn comparison, you will find a signal s1 vibration amplitude will be higher then s1 and s2 respectively wavelet decomposition and draw the layers of time-domain spectrum to only a maximum time domain spectroscopy s1 and s2 points after, s2 is more cyclical and smaller magnitude, s2 cyclical enough obviously, and the vibration is too dense. End domain spectral analysis after the beginning of the spectrum analysis, the first of the original signal s1 and s2fft conversion to give the spectrum, as shown, and then after the high frequency part of wavelet analysis fft transformation to make spectrum. We found that after the comparison, at f 2375HZ out (i.e. the gear mesh frequency), there will be a sharp increase in the amplitude spectrum of the signal s1, and then, the amplitude of the ha)
    2017-01-17 19:18:02下载
    积分:1
  • directanalogsinthesys
    simulink file for direct analog frequency sinthesys
    2009-11-05 02:09:24下载
    积分:1
  • Exact_BER__tools
    this is the matlab simulation for BER exaction
    2014-09-09 00:02:21下载
    积分:1
  • 696518资源总数
  • 104360会员总数
  • 40今日下载