-
disparitymap
立体匹配 获得立体图像左右视图的视差图代码(Stereo matching to obtain three-dimensional view of the disparity map image around the code)
- 2010-10-12 22:03:59下载
- 积分：1
-
Optimazation
This file is to optimize functions
- 2010-11-27 11:24:58下载
- 积分：1
-
bianyuanjiance-juti
二值化后边缘检测算法具体实现，用matlab编写的，有roberts,sobel,prewitt,log等算法的具体实现(value after two edge detection algorithm to realize the use of Matlab prepared, roberts, segmentation, prewitt, log, etc. of specific algorithm implementation)
- 2007-04-22 15:42:44下载
- 积分：1
-
Monte-Carlo-simulation-of-QPSK
This is Monte Carlo simulation of a QPSK communication system
- 2015-01-31 14:11:06下载
- 积分：1
-
negentest_01_defl_gauss
A Deflationary fastICA using negentropy approximation implementted in Matlab
- 2009-04-25 16:45:04下载
- 积分：1
-
matlab-wenzishibie
该算法用matlab编写，并且实现对文字识别。附带图片。(the algorithm using Matlab preparation, and to achieve recognition for words. Photo attached.)
- 2007-05-20 14:40:45下载
- 积分：1
-
zhijiezhuanju
同步电机直接转矩控制的mdl控制 使用转矩和磁链给定 可以很好的跟踪给定值(Synchronous Motor Direct Torque Control mdl control the use of torque and flux can be a good track given setpoint)
- 2013-08-25 19:39:59下载
- 积分：1
-
point2line
good file character recogition
- 2012-05-09 20:46:13下载
- 积分：1
-
OFDM_rece_matlab
一个OFDM符号128个有效符号，插入128个虚拟子载波
符号率（即有效数据率）fsymbol，而发送速率（需要包括虚拟子载波）2fsymbol
输入的数据需要2倍的发送数据率，以便进行内插，实现位定时跟踪，即4倍fsymbol采样率的调制信号
OFDM symbol Nfft=128 points
一个OFDM符号数据点 Nfft*2 = 256 ， Guard Interval点 ＝Ng*2=64
( a OFDM symbol 128 effective symbols, insert 128 virtual sub-carrier
symbol rate (i.e. valid data rate), and fsymbol sending rate (need to include virtual sub-carrier) 2fsymbol
input data need 2 times the sending data rate for interpolation, realize a timing tracking, namely fsymbol sampling rates four times the modulation signal
OFDM symbol Nfft = 128 points
a OFDM symbol of data points Nfft* 2 = 256, Guard Interval point = Ng* 2 = 64
)
- 2011-05-21 10:28:58下载
- 积分：1
-
shear_mapping_based_on_make_zeta_output_0
This code calculates and plots the shear between two z-levels zlevel1 and zlevel2.
It uses output from files make_zeta_u.c, make_zeta_v.c and
make_zeta_T.c i.e. files bearing names ufile??zlevel.dat,
vfile??zlevel.dat and Tfile??zlevel.dat
- 2011-06-06 11:26:16下载
- 积分：1
|
联系客服（QQ：3324461878）
