登录
首页 » matlab » pi4dqpsk

pi4dqpsk

于 2021-01-11 发布 文件大小:1794KB
0 107
下载积分: 1 下载次数: 105

代码说明:

  pi/4-dqpsk 调制解调 的 matlab 仿真,通过srrc滤波器实现16倍的上采样(pi/4-dqpsk modulation and demodulation matlab simulation, through srrc filter to achieve 16 times the sampling)

文件列表:

qpskpi4.m,3492,2013-09-04
π_4-DQPSK调制解调算法.pdf,1923095,2013-09-04

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • matlab
    《MATLAB实用指南》系列丛书DE源代码()
    2008-03-21 17:18:39下载
    积分:1
  • dip3
    A sample code for matlap in dip
    2011-04-22 11:47:34下载
    积分:1
  • Multi_userSignalDetection
    实现了用匹配滤波器对多用户信号中的期望用户进行检测(Achieved with a matched filter on the multi-user signal detection in the hope that users)
    2010-05-24 17:32:09下载
    积分:1
  • KANON
    MATLAB 通过语音合成 《卡农》 采用的纯模拟的方法,(MATLAB through speech synthesis " Canon" pure simulation method,)
    2013-04-16 21:42:48下载
    积分:1
  • cpso
    根据cpso算法给出的一个matlab代码,全,添加测试函数即可运行(According cpso given an algorithm matlab code, full, add test functions to run)
    2014-01-21 10:28:01下载
    积分:1
  • Boost_Converter
    说明:  升压转换器是一种DC / DC电源转换器,可将电压从其输入(源)升至其输出(负载)。在连续导通模式下(流经电感的电流永远不会降为零),升压转换器的理论传递函数为: 占空比在哪里0.5 在此示例中,转换器从250 V电源馈送RC负载,并且PWM频率设置为31 kHz。 模拟 运行仿真并观察示波器上的波形。确认负载电压(Vout)的平均值非常接近理论值:Vout = 250 /(1- 0.5)= 500V。(A boost converter is a DC/DC power converter which steps up voltage from its input (source) to its output (load). In continuous conduction mode (current through the inductor never falls to zero), the theoretical transfer function of the boost converter is: where is the duty cycle.0.5 In this example, the converter is feeding an RC load from a 250 V source and the PWM frequency is set to 31 kHz. Simulation Run the simulation and observe waveforms on Scope. Verify that the mean value of the load voltage (Vout) is very close to the theoretical value of: Vout = 250 / (1 - 0.5) = 500 V.)
    2020-03-22 20:41:56下载
    积分:1
  • dghm
    自适应的多小波阀值算法,利用多小波去除噪声的matlab源代码(Multiwavelet adaptive threshold algorithm, using wavelets to remove noise in many source code matlab)
    2009-04-08 16:29:06下载
    积分:1
  • nmfpack
    用于人脸识别的NMF分解程序,用MATLAB编写的(face recognition for the NMF decomposition process, the preparation of MATLAB)
    2007-05-14 15:48:28下载
    积分:1
  • simulation
    在一个移动通信系统中,发射信号是一个未调制的音频x(t)=cos(2πft),其中f=f0+fi。设标称载波为f0=1GHz,并设fi =512Hz。假定移动用户在一个繁忙的高速公路上距离基站l公里处的地方,从开始从每小时60公里的速度开始,其速度(在0.01秒的时间间隔内测量)以1/2的概率随机的增加或减少1/10公里每小时。试仿真移动用户在这2s的时间间隔内所接收到的信号(及其频谱)。接收信号可以表示为: y(t)=a(t)Cos[2π(fo+f1)(t-△t)] 式中 △(t)=d(t)/c 且 a(t)=k/d2(t) 在上面的表达式中d(t)是在t时刻基站与移动用户的距离,c是光速,△(t)是传播延迟,而a(t)是信号在t时刻的衰减,并假设在这2s内a(t)是一个常数。利用复低通等效模型来进行仿真。(In a mobile communication system, the transmitted signal is an unmodulated audio x (t) = cos (2πft), where f = f0+ fi. Let nominal carrier of f0 = 1GHz, and set fi = 512Hz. Assume that mobile users on a busy motorway station l kilometers place, starting the beginning of 60 kilometers per hour, the speed (measured in 0.01 second interval) to increase the probability of a random 1/2 or reducing 1/10 km/h. Simulation test signal which the mobile subscriber in the 2s time intervals of the received (and its spectrum). The received signal can be expressed as: y (t) = a (t) Cos [2π (fo+ f1) (t- △ t)] Where △ (t) = d (t)/c And a (t) = k/d2 (t) In the above expression, d (t) at time t is a base station and a mobile user s distance, c is the speed of light, △ (t) is the propagation delay, and a (t) is the attenuation of the signal at time t, and assuming that 2s within a (t) is a constant. Using complex low-pass equivalent model for emulation.)
    2015-11-24 17:16:20下载
    积分:1
  • signal
    说明:  信号采样 欠采样 过采样 临界采样 信号频谱 采样频率(Signal sampling undersampling oversampling critical sampling signal spectrum sampling frequency)
    2020-12-01 15:19:27下载
    积分:1
  • 696518资源总数
  • 104269会员总数
  • 42今日下载