▍1. STM8_Freemodbus
基于stm8s的freemodbus协议移植(Transplantation of freemodbus protocol based on stm8s)
基于stm8s的freemodbus协议移植(Transplantation of freemodbus protocol based on stm8s)
BlueCore4 Datasheet BC417143 ·APF有源滤波控制器程序,因为改代码 ·利用51单片机实现DS1302的驱动,以C ·利用STM8L实现诺基亚5110液晶的驱动 ·盛群单片机指令集:简体中文,PDF格 ·SHT11 程序,I2C总线方式。写I2C时 ·7寸彩屏 STM32的固件库3.5 FSMC驱动 ·一种伺服电机的PID控制算法,可以完 ·基于Atmega16单片机的机器人行走、 ·51单片机驱动2.6英寸触摸液晶屏幕, ·stm32 pwm 固件库 大连理工大学 信 ·无线传感网络基础 wireless sensor ·LPC11u14芯片的系统时钟驱动
说明: 基于无功补偿控制器的MODBUS实现,用于高低压无功补偿控制器及其应用算法(Realization of Modbus based on reactive power compensation controller)
使用stm32f407单片机的CAN通信控制驱动电机,并且该程序可以通过红外遥控(CAN communication with stm32f407 MCU is used to control the driving motor, and the program can be controlled by infrared remote control.)
说明: 使用stm32f407单片机的CAN通信控制驱动电机,并且该程序可以通过红外遥控(CAN communication with stm32f407 MCU is used to control the driving motor, and the program can be controlled by infrared remote control.)
MSP430F5529开发板的蜂鸣器例程(MSP430F5529 development board routines buzzer)
数控直流电源,通过4*4按键输入所需电压,PWM调节BUCK电路的开关管的导通时间调节到你所需的电压(NC DC power supply via 4* 4 keypad enter the desired voltage, PWM BUCK regulator circuit switch conduction time adjusting to your desired voltage)
GSM模块AT命令组装和AT命令响应解析程序。实现了自动组装标准AT命令并发送到GSM模块,同时可以提取GSM模块输出的所有AT命令,同时实现了大量AT命令响应的解析工作。主要的过程采用了Contiki的进程模型。(Making and parsing routine for AT commands of GSM module. It can automatically make standard AT commands and sent it to GSM module, while it can get all the AT commands sending GSM module, and analysis a large number of AT command responses. The main process uses a process model of Contiki.)
利用SPI总线读取MPU6000的值,传感器数据准备好后产生外部中断进而触发STM32去读取(The SPI bus read MPU6000 value, the sensor data is ready and then generate an external interrupt trigger STM32 to read)
利用SPI总线读取MPU6000的值,传感器数据准备好后产生外部中断进而触发STM32去读取(The SPI bus read MPU6000 value, the sensor data is ready and then generate an external interrupt trigger STM32 to read)
I2C转UART,51单片机普通IO口模拟I2C从机,解决UART不够的问题(I2C switch to UART, 51 Microprocessor Analog IO port I2C slave address the problem of insufficient UART)
求数字系统设计的与非门简化的立方体运算的质立方体的选拔法程序(digital system design for the door with a simplified calculation of quality cube cube method selection procedures)
I2C的oled加键盘显示的程序。基于STM32F103 (I2C The program oled display and keyboard. Based STM32F103)
说明: 单片机接口8255控制输出,包括单片机电路仿真图、C程序设计代码(MCU interface 8255 control output)
液晶显示器与单片机接口电路程序,实现液晶显示对于信号源发生信号的控制和显示(LCD and microcontroller interface circuit procedures, LCD occurred signal source for the control signal and display)