-
fangzhen1
用matlab进行信号的仿真实验，测量滤波后的混合信号的幅度和相位差。(Signal using matlab simulation, measurement of mixed-signal after filtering of the amplitude and phase difference.)
- 2008-01-08 14:06:09下载
- 积分：1
-
rayleigh-chan
程序仿真了瑞利信道，分析和大量实测表明，多径效应使接收信号包络变化接近瑞利分布。在典型移动通信中，衰落深度达30dB左右，衰落速率约30~40次/秒。(Rayleigh channel simulation procedures, analysis and extensive test shows that the received signal multipath effect changes in the envelope close to the Rayleigh distribution. In a typical mobile communication, fading depth of about 30dB, the decline rate of about 30 to 40 times/sec.)
- 2013-09-21 00:25:14下载
- 积分：1
-
mybode
绘制控制系统近似bode图，为了做自动控制原理作业时偷点懒。虽然matlab自带bode函数但是作业要求画近似的。(Drawing control system approximation bode diagram, when you steal lazy to do the job of Automatic Control Theory. Although matlab function but the job comes bode asked to draw approximate.)
- 2017-03-24 22:13:43下载
- 积分：1
-
test_pcd
三维点云数据测试样本，可以使用MATLAB进行编程(Three dimensional point cloud data test samples, you can use MATLAB to program)
- 2016-09-26 09:46:29下载
- 积分：1
-
Alamouti_2x1_ant_selection
在MIMO 2x1天线选择系统中，利用Alamouti编码，计算系统的BER(In the 2x1 antenna selection, the use of Alamouti coding, computing system BER)
- 2010-11-01 17:33:49下载
- 积分：1
-
BilinearInterpolation
这种双线性插值的matlab源代码,学生需要可以下载使用(This kind of bilinear interpolation of matlab source code, students in need can be used to download
)
- 2014-11-29 11:03:45下载
- 积分：1
-
Sum_rate-maximization-
在已知两源节点，中继节点发射功率的前提下，怎样选择放大系数能够得到最大的传输速率(In the known two source node, the relay node to transmit power premise, how to choose the amplification factor can be obtained the maximum transmission rate)
- 2015-03-12 10:33:04下载
- 积分：1
-
5.INTERPOLATION BY CUBIC SPLINE
%This function finds the cubic splines for the input data points (x,y)
%Input: x = [x0 x1 ... xN], y = [y0 y1 ... yN], xi=interpolation points
% KC = 1/2 for 1st/2nd derivatives on boundary specified
- 2019-04-26 01:12:29下载
- 积分：1
-
demod111
MATLAB中 各种PSK相位编码 已添加为压缩文件 绝对好用(MATLAB in a variety of PSK phase encoding has been added to the compressed file is absolutely easy to use)
- 2012-04-16 15:57:11下载
- 积分：1
-
createButtonLabel
buttonIcon = createButtonLabel(string,PVs,figOpt)
Have you ever been frustrated by an inability to label a vertically oriented pushbutton or uicontrol with a string? This function is for you!
All valid Parameter-Value pairs, INCLUDING TEXT ROTATION, are supported. Note that this function requires the Image Processing Toolbox, and that it triggers the creation of a temporary figure, which will be momentarily visible during button-label creation.
- 2009-10-21 15:19:29下载
- 积分：1
