登录
首页 » matlab » codes

codes

于 2010-02-16 发布 文件大小:29KB
0 70
下载积分: 1 下载次数: 3

代码说明:

  program codes on image processing

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • P
    说明:  这里面介绍了很多关与先进PID控制及其MATLAB仿真(This introduced a lot of inside clearance and advanced PID control and MATLAB simulation)
    2008-01-17 23:02:03下载
    积分:1
  • AIRS_Classification
    this program is about airs algorithm iti role is bout classification of many vectors of data
    2014-02-24 17:33:19下载
    积分:1
  • space-deinterlacing
    空间线性去隔行算法,有效改善运动图像的去隔行效应(Linear space de-interlacing algorithm, to effectively improve the movement effect of image de-interlacing)
    2009-05-17 20:03:42下载
    积分:1
  • VPC
    vowel _phenome _classification
    2011-01-13 16:23:54下载
    积分:1
  • nnToolKit_cb
    说明:  C++BUILDER与MATLAB实现混合编程源代码(C++ BUILDER realize mixed language programming with the MATLAB source code)
    2008-10-01 08:58:03下载
    积分:1
  • eee
    杨氏双缝干涉 两相干光源到接收屏上P点距离r1=(D2+(y-a/2)2)1/2, r2=(D2+(y+a/2)2)1/2, 满足相干条件的光波叠加后,对于观察屏上某一确定点,即r1、r2确定后,叠加后的光强为 式中λ为光波的波长, 、 ,令相位差φ=2π(r2-r1)/λ, 最后可得公式如下: , 最后光强I=4I0cos2(Φ/2)。 观察相干光叠加后光强的分布. (Young' s double slit interference two coherent light source to the point P on the receiving screen distance r1 = (D2+ (YA/2) 2) 1/2, r2 = (D2+ (y+a/2) 2) 1/2, meet coherent conditions lightwave after superposition, for a determined point on the viewing screen, i.e. R1, R2 is determined, the superimposed light intensity where λ is the wavelength of light, make the phase difference φ = 2π (R2-R1)/λ, final can be obtained using the following formula: Finally, the light intensity I = 4I0cos2 (φ/2). Observed coherent superposition of light intensity distribution.)
    2013-01-03 21:04:13下载
    积分:1
  • RotmanLensSParam
    Rotman lens S-parameters matrix calculation
    2011-11-04 22:28:53下载
    积分:1
  • matlab
    设计一个一位二进制数大小比较器。比较两个一位二进制数A和B的大小,电路有三个输出端Y1,Y2和Y3,分别对应A大于B,A等于B,A小于B。当条件满足时,相应输出端为1,否则为0。(A,B用两个脉冲源代替),建立仿真模型并保存。(Design a one binary magnitude comparator. A size comparison of two binary numbers A and B, the circuit has three outputs Y1, Y2 and Y3, respectively, corresponding to the A greater than B, A is equal to B, A less than B. When the conditions are met, the corresponding output is 1, and 0 otherwise. (A, B instead of the source with two pulses), and save the simulation model.)
    2013-12-24 13:16:27下载
    积分:1
  • 利用测井曲线合成地震记录序synthetic-by-welllog-data
    利用测井曲线合成地震记录程序,这是一个例子,其中有AVO的井资料(This is a program that make a seismic synhetic data by welllog data, and the AVO well data is in it. )
    2016-08-10 15:51:23下载
    积分:1
  • eof
    eof分解的程序 好用且可直接使用 适合于海洋和大气学科(eof analysis for oceanography and meterology)
    2010-05-07 13:14:19下载
    积分:1
  • 696518资源总数
  • 104269会员总数
  • 42今日下载