-
Chirp_Pulse_Comp
chirp信号脉冲压缩，用于雷达信号处理，产生chirp信号后进行压缩，以实现高距离分辨力(chirp signal pulse compression for radar signal processing to generate chirp signal is compressed in order to achieve high range resolution)
- 2009-12-21 17:31:21下载
- 积分：1
-
acquisition-for-DF
说明： 这是一篇关于GPS信号的捕获文章，采用的是DF差分相关捕获的算法，具有在较低信噪比的情况下捕获信号(This is an article about the capture of GPS signal, using the DF algorithm to capture differential associated with low signal to noise ratio in the case of capture signal)
- 2011-03-09 15:14:39下载
- 积分：1
-
EHO
象群游牧算法（EHO）原始代码（作者所写）。(Elephant herding optimization algorithm (EHO) original codes (the author wrote).)
- 2018-10-02 19:33:12下载
- 积分：1
-
photonic_crystal
采用平面波展开法模拟2维光子晶体的能带结构,FDTD法模拟2维光子晶体能量传输(used plane wave expansion method for simulation of two-dimensional photonic crystal structure of the band, FDTD simulation of two-dimensional photonic crystal energy transmission)
- 2021-04-27 10:18:44下载
- 积分：1
-
erjiguanyingyong
文章介绍了二极管多种应用电路很实用的模电资料
(failed to translate)
- 2011-05-25 15:11:05下载
- 积分：1
-
Q3
说明： car parking correctly by Fuzzy controller TS method
- 2015-01-26 02:13:19下载
- 积分：1
-
mean-shift
meanshift算法的中文入门资料，介绍的很详细(meanshift s Algorithm Chinese introduction material, introduction is very detailed)
- 2013-01-28 18:23:38下载
- 积分：1
-
baoluo
在labview的信号处理中用户来计算波形的包络谱，用来进行信号分析(To calculate the wave spectrum envelope of users in the signal processing of the LabVIEW, used for signal analysis)
- 2013-12-30 09:37:49下载
- 积分：1
-
my_ACO_OFDM
matlab实现了OFDM功能，ACO-OFDM可以在可见光中使用。(Orthogonal frequency division multiplexing (OFDM)
is a modulation technique which is now used in most new and
emerging broadband wired and wireless communication systems because it is an effective solution to intersymbol interference caused by a dispersive channel. )
- 2015-05-30 09:30:56下载
- 积分：1
-
nefcon
模糊神经网络采用matlab编程 o install NEFCON follow these steps: 1. Unpack the tar file NEFCON.TAR into your MATLAB working directory: tar xf NEFCON.TAR 2. Start MATLAB 3. Change to the installation directory. 4. Change to the NEFCON directory. 5. Start the STARTUP M-file to initialize NEFCON.(FNN using Matlab programming o install NEFCON follow these steps : 1. Unpack the tar file NEFCON.TAR MATLAB into your working directory : tar xf NEFCON.TAR 2. Start MATLAB 3. Change to the installation directory. 4. Change to the NEFCON directory. 5. Start the STARTUP M-file to initialize NEFCON.)
- 2005-06-13 12:11:26下载
- 积分：1
