-
COM
基于CVI2010的串口编程 使用C++ 适合初学者学习(Based on CVI2010 serial port programming using c++ for beginners to learn)
- 2015-05-13 09:41:31下载
- 积分：1
-
3Ddisplay
Labview 3D显示物体姿态。单片机采集传感器数据，通过串口传至电脑，labview接收数据并截取处理，通过3d控件显示。(The labview 3D display object attitude. Single-chip sensor data collected and transmitted to the computer through the serial port, labview receive data and the interception of the processing, 3d controls.)
- 2020-07-09 16:38:55下载
- 积分：1
-
Example-send-rece
用 C++ 编写的 发送 接收串口工其软件，好用，可以参考一下(C++ prepared by the transmission and receiving serial software, good use, you can refer to)
- 2015-12-21 18:45:54下载
- 积分：1
-
serial
可以向串口发送数据，或从指定串口接收数据 VC源码-基础编程-源程序代码免费注册下载(Can send data to a serial port, or from specified serial ports receive data source-basic programming VC-source code downloaded free registration
)
- 2011-12-12 11:39:33下载
- 积分：1
-
SerialPortTest
简单的串口调试，能够实行发送和接收字符。(Serial easy debugging, it is able to implement send and receive characters.)
- 2009-03-10 10:57:16下载
- 积分：1
-
[c023]RS232串口通讯示例源码
说明： 通过串口来通信，控制PLC，单片机各种伺服变频等实现运动。(Through serial port to communicate, control PLC, microcontroller servo frequency conversion and so on to achieve movement.)
- 2020-06-24 02:00:02下载
- 积分：1
-
SEEDdrivers
合众达提供的两个驱动，可以添加自己的算法。一个是串口的，一个是实时系统的。(America to the two drivers, they can add their own algorithms. 1 serial port, a real-time system.)
- 2007-06-11 09:53:13下载
- 积分：1
-
auproved
本文提出在数字移动通信中子带滤波器组处理可以提高不同阵元信号的相关性,从而能改善自适应阵列抑制码间干扰(ISI)和共信道干(In this paper, it is proposed that the correlation of different array element signals can be improved by processing the subband filter banks in digital mobile communication, thus the adaptive array suppression inter-symbol interference (ISI) and the co-channel stem can be improved.)
- 2018-09-28 12:48:18下载
- 积分：1
-
6
说明： 串口通讯实验：
本实验得到的结果为，打开超级终端，设置波特率为115200，数据流控制位为无。运行系统，就会显示“UART & Interrupt Experiment,Please Input from the keyboard”，我们就可以通过写串口操作。
在flash调试时，需要修改RO BASE为0x00000000，其他不用修改，重新编译下载就可运行。
注意：由于系统产生中断，程序计数器就会跳到0x18处执行中断服务子程序，所以不能在SDRAM调试。 (Serial communication experiment: the results of this experiment, open HyperTerminal, set the baud rate to 115200, data flow control bit is not. Operating system, it will display " UART & Interrupt Experiment, Please Input from the keyboard" , we can write the serial port operation. Debug in flash, you need to modify the RO BASE is 0x00000000, the other not modify, recompile download can run. Note: Due to system interrupt, the program counter will jump to 0x18 Department execute the interrupt service routine, it can not debug the SDRAM.)
- 2010-09-01 22:57:00下载
- 积分：1
-
serial
实现labview的串口通讯，控制下位机两路继电器，以及控制电机旋转。(Achieve labview serial communication, the next crew to control two relays, as well as to control the motor rotation.)
- 2016-08-15 14:57:30下载
- 积分：1
