登录
首页 » SCM » 主要考虑处理速度、功耗、程序存储器和数据存储器的容量、片内的资源,如定时器的数量

主要考虑处理速度、功耗、程序存储器和数据存储器的容量、片内的资源,如定时器的数量

于 2023-08-09 发布 文件大小:32.92 kB
0 99
下载积分: 2 下载次数: 1

代码说明:

主要考虑处理速度、功耗、程序存储器和数据存储器的容量、片内的资源,如定时器的数量-Main considerations deal with speed, power, program memory and data memory capacity, on-chip resources, such as the number of timer

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 这是一份I2C数据传输程序.自己写的,有识之士看看,
    这是一份I2C数据传输程序.自己写的,有识之士看看,-I2C data transmission procedures. Wrote it myself, people of insight to see,
    2022-02-09 23:30:20下载
    积分:1
  • SCM C program design and application examples
    单片机C程序设计及应用实例的例子-SCM C program design and application examples
    2022-02-05 09:32:10下载
    积分:1
  • 51单片机C语言多种点阵屏驱动程序(开发软件为keil C
    51单片机C语言多种点阵屏驱动程序(开发软件为keil C ---8字点阵屏左移程序,64_16点阵屏驱动程序,上移显示程序,左移显示程序)51 monolithic integrated circuit C language many kinds of lattice screen driver (develops the software is keil C ---8 character lattice screen left shift procedure, the 64_16 lattice screen driver, uppers shift the display sequence, the left shift display sequence -51 Singlechip C language a variety of dot-matrix screen driver (development of software for keil C--- 8 character dot matrix screen left procedures 64_16 dot-matrix screen driver, on the shift display program, the left display program) 51 monolithic integrated circuit C language many kinds of lattice screen driver (develops the software is keil C--- 8 character lattice screen left shift procedure, the 64_16 lattice screen driver, uppers shift the display sequence, the left shift display sequence
    2022-05-23 16:35:37下载
    积分:1
  • AVR单片机控制nokia3510i nokia6100液晶显示屏的库文件及例程
    AVR单片机控制nokia3510i nokia6100液晶显示屏的库文件及例程-AVR control nokia3510i nokia6100 LCD screen of the library and routines
    2022-01-28 00:26:05下载
    积分:1
  • 这个是完红外线PT2261的源码,绝对的好用,不要改动。是的中断做的阿...
    这个是完红外线PT2261的源码,绝对的好用,不要改动。是的中断做的阿-This is the End of the PT2261 infrared source, the absolute ease of use, do not change. To do is interrupt the Arab-Israeli
    2022-05-09 09:28:55下载
    积分:1
  • Keil C 编程的手写板
    Keil C 编程的手写板-Keil C Programming 5270
    2022-11-23 11:25:03下载
    积分:1
  • 单片机用T1中断在IO口P1.0输出乐曲(在P1.0口与VCC间接一喇叭即可听到) 1.由于输出的是方波,比较难听:...
    单片机用T1中断在IO口P1.0输出乐曲(在P1.0口与VCC间接一喇叭即可听到) 1.由于输出的是方波,比较难听:-)你也可以将波形细分用DA输出正弦波 2.由于T1频繁中断,任何其他中断发生都会是乐曲打顿,只适合试验 3.优化音符编码:一个字节中包含节拍、音符、升降调,可区分数据和命令 -Single-chip microcomputer used in the IO port T1 interrupt output music P1.0 (P1.0 port with VCC in the indirect one can hear the speaker) 1. As the output is a square wave, more bluntly :-) You can also fine-waveform DA output sine wave with sub-2. Due to the frequent interruption of T1, any other interruption occurs Dayton will be playing music, is only suitable for test 3. optimized coding notes: A byte contains rhythms, notes, take-off and landing tune can distinguish between data and command
    2022-03-26 02:09:22下载
    积分:1
  • 12864中文说明,我认为很有用,希望关照
    12864中文说明,我认为很有用,希望关照-12864 Chinese note, I think very useful, I hope take care! ! ! !
    2022-03-21 04:05:25下载
    积分:1
  • PHilips 4路A/D+1路D/A芯片控制C程序
    PHilips 4路A/D+1路D/A芯片控制C程序-PHilips four A/D Road, a D/A chip control procedures C
    2022-07-04 07:09:31下载
    积分:1
  • 编写一个延时1MS子程序根据题目选择是定时还是记数状态,本题选择记数状态。然后根据延时1MS计算出计时器的初值是E0H(高8位)18H(低5位)。最后编写算法,...
    编写一个延时1MS子程序根据题目选择是定时还是记数状态,本题选择记数状态。然后根据延时1MS计算出计时器的初值是E0H(高8位)18H(低5位)。最后编写算法,对T0初始化,利用T0的中断TF0调用中断处理程序。-prepared a delay rungs subroutine under the topic chosen is not a time to memorize numbers or state of mind of the few options that state. According to delay timer rungs calculate the initial value is E0H (high 8) 18H (Low 5). Preparation of the final algorithm, the T0 initialization, interrupt the use of T0 TF0 call interrupt handling procedures.
    2022-01-25 22:40:39下载
    积分:1
  • 696518资源总数
  • 106215会员总数
  • 5今日下载