登录
首页 » SCM » 单片机实现CAN总线,SJA1000的驱动程序

单片机实现CAN总线,SJA1000的驱动程序

于 2023-06-24 发布 文件大小:2.91 kB
0 147
下载积分: 2 下载次数: 1

代码说明:

单片机实现CAN总线,SJA1000的驱动程序-Realize single-chip CAN bus, SJA1000 driver

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • ARM程序,很好的学习资料
    ARM程序,很好的学习资料-ARM program, good learning materials
    2022-07-15 16:20:21下载
    积分:1
  • TECHWELL 之tw2835 四画面合一之驱动代码,CCIR656输出,KEIL C51 平台编译,...
    TECHWELL 之tw2835 四画面合一之驱动代码,CCIR656输出,KEIL C51 平台编译,-Techwell tw2835 of one of four screen-driven code, CCIR656 output, KEIL C51 compiler platform,
    2022-06-18 10:42:16下载
    积分:1
  • 奉献:485 [日期:2005
    奉献:485 [日期:2005-11-29] 来源:侃单片机 作者:etiller [字体:大 中 小] -Dedication: 485 [Date :2005-11-29] Sources: McCain Singlechip Author: etiller [Font: Xinhuanet]
    2022-05-10 12:55:15下载
    积分:1
  • “供应链管理原理与实践技术”1章
    《单片机原理与实用技术》第1章-"SCM principles and practical technology," Chapter 1
    2022-05-17 04:58:11下载
    积分:1
  • MSP430
    MSP430驱动D/A芯片DA8303 C语言程序-MSP430-driven D/A chip DA8303 C Language Program
    2022-03-23 19:56:30下载
    积分:1
  • SLE4442IC卡存储程序 单片机是P89LPC9
    SLE4442IC卡存储程序 单片机是P89LPC9-SLE4442IC storage cards procedures SCM is P89LPC9
    2023-08-15 14:20:05下载
    积分:1
  • 我上传了一些信息,单片机,keil软件,希望对大家有帮助
    我上传的一些单片机的资料,KEIL软件的使用,希望对大家有帮助-I uploaded some information on SCM, KEIL software, I hope all of you help
    2022-01-24 14:53:15下载
    积分:1
  • 美信公司的单总线温度传感器DS18B20的温度测量程序,供参考。...
    美信公司的单总线温度传感器DS18B20的温度测量程序,供参考。- Beautiful letter company s single main line temperature sensor DS18B20 temperature survey procedure, for reference.
    2022-02-22 06:42:55下载
    积分:1
  • 三相步进电机的三相六拍工作方式,正转的绕组通电顺序:A、AB、B、BC、C、CA、A,反转的通电顺序:A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性,故步进电机的工作过程中不能及时的启动和停止,在启动时应慢慢的加速到预定速度,在停止前应逐渐减速到停止,否则,将产生失步现象。 步进电机的控制问题可总结为两点: 1、产生工作方式需要的时序脉冲; 2、控制步进电机的速度,使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.
    2022-07-20 15:21:46下载
    积分:1
  • 这是通信接口实验,";DA转换原理的表达。
    这是通讯接口实验《DA转换原理实验》的原理程序,适合于那些上嵌入式系统、通信、计算机专业的人-This is the communication interface experiment, "DA conversion principle experiment," the principle procedures, suitable for those on embedded systems, communications, computer specialists in the
    2022-05-27 10:56:56下载
    积分:1
  • 696518资源总数
  • 106215会员总数
  • 5今日下载