-
用c语言编写的单片机秒表程序,该程序能够实现从0
用c语言编写的单片机秒表程序,该程序能够实现从0-59-With c languages Singlechip stopwatch program, the program can be realized from 0-59
- 2022-01-26 03:39:51下载
- 积分:1
-
ZLG7289测试程序,用于调整你的程序,网站上下载的程序不能正常显示,使用ATMEL公司的Atmega单片机...
ZLG7289测试程序,用于调整你的程序,网站上下载的程序不能正常显示,使用ATMEL公司的Atmega单片机-ZLG7289 testing procedures used to adjust your procedures, site to download the program should not display properly, use the ATMEL ATmega company
- 2022-03-11 22:16:30下载
- 积分:1
-
gccavr书籍内容包含gcc应用安装及对avr下载说明和电路的配置
gccavr书籍内容包含gcc应用安装及对avr下载说明和电路的配置-gccavr books contain the installation and application of gcc right avr download notes and circuit configuration
- 2022-08-15 15:05:30下载
- 积分:1
-
能够将语音先进行录制,然后在回放,适合应用在一些需要语音播报功能的设备上...
能够将语音先进行录制,然后在回放,适合应用在一些需要语音播报功能的设备上-Able to carry out a voice recording, playback and then, suitable for broadcast in a number of the needs of voice-enabled devices on the
- 2022-02-19 22:52:38下载
- 积分:1
-
MSP430 MCU own some of the information collected by those who need it download
msp430单片机的一些
资料
自己收集的一些有需要的请下载-MSP430 MCU own some of the information collected by those who need it download
- 2023-07-31 22:00:04下载
- 积分:1
-
让实验板上八个数码管循环显示0
让实验板上八个数码管循环显示0-9十个数-Let the experiment on-board digital control cycle showed that eight of ten the number of 0-9
- 2022-03-19 08:20:40下载
- 积分:1
-
LT_1B msp430开发板例子程序-TA_6
LT_1B msp430开发板例子程序-TA_6
- 2022-10-22 12:05:03下载
- 积分:1
-
Done before the use of C51, the feeling is not quick enough, a bit flash, try to...
之前用C51做了,感觉不够快,有点闪,试着移过来用M8做。 -Done before the use of C51, the feeling is not quick enough, a bit flash, try to move up to do with M8.
- 2022-07-18 11:21:45下载
- 积分:1
-
MSP430F1121 with the LCD driver chip PCF8576 connection procedures
MSP430F1121与液晶驱动芯片PCF8576的连接程序-MSP430F1121 with the LCD driver chip PCF8576 connection procedures
- 2022-03-14 14:31:59下载
- 积分:1
-
功能:
1、作为主机通讯采集两路下位机数据并将此数据通过8255送出(十路水位值)
并计算水头送STC板
2、采集数据为BCD码制,先转换成二进制...
功能:
1、作为主机通讯采集两路下位机数据并将此数据通过8255送出(十路水位值)
并计算水头送STC板
2、采集数据为BCD码制,先转换成二进制,处理后再转换成BCD
3、通讯采用方式3,多机通讯,上位机发地址时TB8=1,其他TB8=0
下位机SM2=1,RB8=1时产生中断后使SM2=0收发数据,结束后SM2=1
在此系统中本机硬件地址要设为0-Features: 1, as the host of two-way communication acquisition of data-bit machine and send this data through 8255 (the road level 10 value) and calculate the head sent to STC board 2, for BCD code data collection system, the first converted into binary, and then deal with the conversion into BCD 3, communication using methods 3, multi-machine communications, address PC made TB8 = 1, other TB8 = 0 under the digital machine SM2 = 1, RB8 = 1 when the failure to make SM2 = 0 to send and receive data, after the end of SM2 = 1 in this system to the local hardware address set to 0
- 2023-07-17 03:30:03下载
- 积分:1