-
自己的51实习是做得数字时钟，可以调整时间，可以显示当前温度。...
自己的51实习是做得数字时钟，可以调整时间，可以显示当前温度。-51 is doing his internship digital clock, you can adjust the time, you can display the current temperature.
- 2022-03-26 18:55:57下载
- 积分：1
-
ht9200B C51编程子程序和HT9200A和资料
ht9200B C51编程子程序和HT9200A和资料-ht9200B C51 programming routines and information and HT9200A
- 2022-05-20 03:43:16下载
- 积分：1
-
采用IAR在线调试ADI公司基于ARM7内核的ADUC7026的ExternalMemory代码
采用IAR在线调试ADI公司基于ARM7内核的ADUC7026的ExternalMemory代码-IAR debug using online ADI Corporation ADUC7026 based on ARM7 core of ExternalMemory code
- 2022-03-06 20:38:58下载
- 积分：1
-
485 are way communication. Through 485 to control a group of light switches.
通信方式是485方式。通过485来控制一组灯的开关。-485 are way communication. Through 485 to control a group of light switches.
- 2022-03-07 13:39:35下载
- 积分：1
-
利用串口和单片机进行通讯,VC用对话框实现
利用串口和单片机进行通讯,VC用对话框实现-use serial communication and microcontroller, the VC using Dialog
- 2023-03-13 06:35:04下载
- 积分：1
-
51单片机开发板，有数码管、按键、数模转换、液晶显示
51单片机开发板，有数码管、按键、数模转换、液晶显示-51 MCU development board, with digital control, buttons, digital-analog conversion, liquid crystal display, etc.
- 2022-01-22 05:39:09下载
- 积分：1
-
本程序用于用单片机控制步进电机的转动。用单片机的某一个引脚实现控制，如果引脚电平为高则实现正转，反之为反转。所用单片机为日立系列h83664十六位单片机。本代码...
本程序用于用单片机控制步进电机的转动。用单片机的某一个引脚实现控制，如果引脚电平为高则实现正转，反之为反转。所用单片机为日立系列h83664十六位单片机。本代码使用c语言实现，开发环境为日立系列单片机专用开发环境-This procedure for the use of single-chip stepper motor rotation control. With a pin MCU control, if the pin level is higher then realize to the contrary, for the inversion. Used in single-chip for Hitachi Series 16 Singlechip h83664. This code uses the c language, development environment for the Hitachi series of single-chip dedicated development environment
- 2023-01-07 10:45:03下载
- 积分：1
-
At can be given its arguments in a file. You can comment
out lines by precedin...
At can be given its arguments in a file. You can comment
out lines by preceding them with either # or -
characters. This is an easy way to temporarily disable
some commands.
The CONTINUE-command is most useful at the end of the
file. When this command is read, the file is started
again from the beginning. You can use it situations where
the machine is not shut down for the night and you want
to run some commands every day.- At can be given its arguments in a file. You can comment
out lines by preceding them with either# or-
characters. This is an easy way to temporarily disable
some commands.
The CONTINUE-command is most useful at the end of the
file. When this command is read, the file is started
again from the beginning. You can use it situations where
the machine is not shut down for the night and you want
to run some commands every day.
- 2022-02-21 09:29:04下载
- 积分：1
-
s3c44b0x ch375 and U disk read and write procedures
s3c44b0x和ch375读写U盘程序-s3c44b0x ch375 and U disk read and write procedures
- 2022-01-26 04:09:23下载
- 积分：1
-
51 MCU after cutting TCP/IP protocol, the compiler environment, Keil C51.
51单片机实现经过裁剪的TCP/IP协议,编译环境Keil C51.-51 MCU after cutting TCP/IP protocol, the compiler environment, Keil C51.
- 2022-02-11 12:19:50下载
- 积分：1
