登录
首页 » 嵌入式系统 » STM32103 数采程序

STM32103 数采程序

于 2023-01-22 发布 文件大小:13.40 MB
0 98
下载积分: 2 下载次数: 1

代码说明:

应用背景 数采装置可配合SQL数据库,实现数据采集并存储到服务器的功能,方便对采样数据进行分析、读取,为产品开发或设备的运行情况进行检测、检验,其实际用途颇广。 关键技术基于STM32F103芯片,自制数采装置,数采程序,可用于多路信号采集(如:电压、电流等信号),并通过串口上传至服务器,实现数据的采集。

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • NIOSII of 7 c language source code, is a seven examples, respectively realize ni...
    NIOSII的7个c语言源码,是7个例子,分别在niosII IDE环境下实现,不同的功能。是基于altera的标准c,目前资源较少。-NIOSII of 7 c language source code, is a seven examples, respectively realize niosII IDE environment, different functions. Is based on the altera standard c, currently fewer resources.
    2022-01-31 09:00:24下载
    积分:1
  • 台达plC内部寄存器与modbus地址映射表,对想用单片机通过modbus协议控制台达PLC的开发人员有帮助,通过触摸屏接口通讯。...
    台达plC内部寄存器与modbus地址映射表,对想用单片机通过modbus协议控制台达PLC的开发人员有帮助,通过触摸屏接口通讯。-Delta plc internal registers with the Modbus address mapping table, and would like to use single-chip through the Modbus protocol Console PLC Tatsu developer help, through the touch screen interface communication.
    2022-08-12 09:23:01下载
    积分:1
  • 8051 基于带领的接口
    #include < REG51F。H > 无符号的 int a、 b ; 无效的延迟 (无符号的 int 时间) ; void main) { = 0x01; P0 = a; while(1) { 无符号的 int x,b,c; = 0x00; b = 0; c = 500 ; 为 (x = 0 ; x < 500 ; x + +) { 请点击左侧文件开始预览 !预览只提供20%的代码片段,完整代码需下载后查看 加载中 侵权举报
    2022-02-04 04:49:37下载
    积分:1
  • 103规约的程序
    103 规约的以太网接入,说明源代码,包括四遥功能设置值板,录得在波兰,当回归,如数模转换器,在泛型侧 IEC103 类别中,主要用于对数据进行分组
    2023-04-06 01:25:03下载
    积分:1
  • EDA高手门必看,FPGA
    EDA高手入门必看,FPGA-CPLD-开发流程。-EDA players see entry, FPGA-CPLD-development process.
    2022-04-17 20:12:57下载
    积分:1
  • 基于stm32f107的CCID通讯的智能卡读卡器
    采用CCID与计算机通讯的智能卡读卡器下位机代码,所有符合CCID规范的上位机均可使用。可用于了解CCID协议的下位机实现,及智能卡T0通讯的具体实现代码。可实现智能卡的ATR,PPS及其他读写命令。
    2022-03-11 15:12:43下载
    积分:1
  • ucgui仿真例程
    仿真例程应ucgui3.9.0函数库包,函数库中实现了多窗口切换,滚动条的滚动实现界面滚动,利用自己写的局部重画方式,下载硬件后仍然比较流畅 
    2022-03-23 00:36:28下载
    积分:1
  • This a Good IDN Client.
    This a Good IDN Client.
    2022-07-02 06:39:01下载
    积分:1
  • VHDL paper prepared for the introduction of procedures and reports. Steps are as...
    本文为采用VHDL编写的程序及报告。步骤如下:1设计三位二进制计数器程序 二:设计一驱动循环显示7位数字 2编写LED控制程序如下: 3设计采用原理图方式如下: -VHDL paper prepared for the introduction of procedures and reports. Steps are as follows : Design of a binary counter three two procedures : Design of a drive cycle show seven figures prepared two LED control procedures are as follows : three designs diagram as follows :
    2022-02-09 14:06:11下载
    积分:1
  • EEPROM 与 STM32 的接口
    (S) 24C64CEEPROM 与 STM32 microcontroller.how 接口将数据存储到 eeprom eeprom 和写数据
    2022-07-12 23:59:07下载
    积分:1
  • 696518资源总数
  • 105678会员总数
  • 22今日下载