-
通过编码开关（旋转编码器）控制数码管的加减一！程序详细的体现了编码器的编程和数码管的单片机的编程！本程序通过AT89C51和24脉冲编码器的测试
通过编码开关（旋转编码器）控制数码管的加减一！程序详细的体现了编码器的编程和数码管的单片机的编程！本程序通过AT89C51和24脉冲编码器的测试-Through coding switch (rotary encoder) control the digital control of plus or minus 1! Procedures in detail the programming reflects the encoder and digital control of the microcontroller s programming! AT89C51 and 24 of this procedure the test pulse encoder
- 2022-06-01 14:06:48下载
- 积分：1
-
基于单片工业控制微机的无线式键盘接口设计,仅占用一根接口线...
基于单片工业控制微机的无线式键盘接口设计,仅占用一根接口线-Single-chip microcomputer-based industrial control wireless keyboard interface design, only with a line interface
- 2023-06-13 02:30:03下载
- 积分：1
-
飞思卡尔单片机MC9S08AW60移植到MC9S08AC60方法(英文)
飞思卡尔单片机MC9S08AW60移植到MC9S08AC60方法(英文)-Freescale
- 2022-12-16 20:35:04下载
- 积分：1
-
定时器结合LED
7805开发板，适合初学者
定时器结合LED
7805开发板，适合初学者-Timer combination LED7805 development board, suitable for beginners
- 2023-09-01 07:25:04下载
- 积分：1
-
Atmel公司的ARM7应用TWI项目相关的可以在IAR直接运行
ATMEL ARM7有关TWI应用设置的程序,可以在IAR中直接运行-ATMEL ARM7 applications related to TWI programs can be run directly in IAR
- 2022-03-06 18:59:05下载
- 积分：1
-
蜂鸣器响
改变蜂鸣器的频率，通过改变延时时间
蜂鸣器的时间要是是靠延时来完成的...
蜂鸣器响
改变蜂鸣器的频率，通过改变延时时间
蜂鸣器的时间要是是靠延时来完成的-Buzzer buzzer ring to change the frequency by changing the delay time if the buzzer is the time to be completed by the time delay
- 2022-02-14 06:38:54下载
- 积分：1
-
一个多媒体液晶显示器内部控制器(主芯片为:7301)的源程序(KC51...
一个多媒体液晶显示器内部控制器(主芯片为:7301)的源程序(KC51-an internal multimedia LCD Controller (Controller chip : 7301) of the source (KC51
- 2022-05-19 10:16:43下载
- 积分：1
-
使用3310液晶
使用3310液晶---数字频率计
.-Use 3310 LCD- digital frequency meter.
- 2022-02-11 16:11:53下载
- 积分：1
-
On the eye to achieve a few procedures, mainly used for electronic communication...
关于眼图实现的几个程序，主要用于电子通信系统设计-On the eye to achieve a few procedures, mainly used for electronic communication system design
- 2022-07-27 12:59:50下载
- 积分：1
-
由8051组成的单片机系统通常情况下，P0口分时复用作为地址、数据总线，P2口提供A15...
由8051组成的单片机系统通常情况下，P0口分时复用作为地址、数据总线，P2口提供A15-A8即高8位地址，P3口用作第二功能，只有P1口通常用作I/0口。P1口是8位准双向口，它的每一位都可独立地定义为输入或输出，因此既可作为8位的并行I/O口，也可作为8位的输入输出端。当工作在输入方式时，对应位的锁存器必须先置1,才能正确地读到引脚上的信号,否则,执行读引脚指令时,若对应位的锁存器的值为0，读的结果永远为0。-By 8051, composed of single-chip microcomputer system under normal circumstances, P0 timeshare I reuse as address, data bus, P2 I provide A15-A8 high eight address, P3 mouth for the second function, I usually only P1 for I/0 I. P1 I was eight quasi-two-way port, it can be independent of each and every defined as input or output, it can be used as 8-bit parallel I/O port, can also be used as 8-bit input and output side. When the work in the input, the corresponding bit latch must first buy one in order to correctly read the signal pin, or pin the implementation of reading instruction, if the corresponding bit latch the value of 0, Reading the results of Forever to 0.
- 2023-08-10 04:55:03下载
- 积分：1
