登录
首页 » SCM » NOKIA线控耳机源码,协议为NOKIA自定义协议。

NOKIA线控耳机源码,协议为NOKIA自定义协议。

于 2022-11-16 发布 文件大小:5.01 kB
0 80
下载积分: 2 下载次数: 1

代码说明:

NOKIA线控耳机源码,协议为NOKIA自定义协议。-NOKIA headset wire source, the agreement for NOKIA custom protocols.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Sunplus 16
    凌阳16位单片机新版SACM_D10语音函数库,语音使用更方便-Sunplus 16-bit single-chip voice SACM_D10 new library, voice, use of more convenient
    2023-01-22 11:20:04下载
    积分:1
  • 平缝机的单片机伺服控制系统源代码。本程序为用单片机控制永磁同步电机的低成本方案...
    平缝机的单片机伺服控制系统源代码。本程序为用单片机控制永磁同步电机的低成本方案-sewing machine SCM servo control system source code. The procedures for the use of SCM control PMSM low-cost programs
    2023-03-25 22:30:03下载
    积分:1
  • simpliciti1.0.4版本,在CC2430上通过实验
    simpliciti1.0.4版本,在CC2430上通过实验-simpliciti1.0.4 version, the CC2430 on the experiments
    2022-02-15 15:16:40下载
    积分:1
  • C51KEY
    用C51编[写的按键运用程序,已在产品中运用-C51KEY
    2022-04-11 02:24:31下载
    积分:1
  • LPC932 MEASURE PROGRAM
    LPC932 MEASURE PROGRAM
    2022-07-19 23:04:33下载
    积分:1
  • ucosII实时操作系统的2.84官方版本,可用于不同处理器的移植
    ucosII实时操作系统的2.84官方版本,可用于不同处理器的移植-ucosII RTOS official version 2.84 can be used for different processors transplant
    2022-11-15 03:05:05下载
    积分:1
  • 三相步进电机的三相六拍工作方式,正转的绕组通电顺序:A、AB、B、BC、C、CA、A,反转的通电顺序:A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性,故步进电机的工作过程中不能及时的启动和停止,在启动时应慢慢的加速到预定速度,在停止前应逐渐减速到停止,否则,将产生失步现象。 步进电机的控制问题可总结为两点: 1、产生工作方式需要的时序脉冲; 2、控制步进电机的速度,使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.
    2022-07-20 15:21:46下载
    积分:1
  • 飞利浦的80C552串口通信代码,可通过PC机完成对单片机的控制,并向上位机返回数据。...
    飞利浦的80C552串口通信代码,可通过PC机完成对单片机的控制,并向上位机返回数据。-80C552 bunches of communication code of Philip, can finish the control on one-chip computer through the PC , and return to the data in the upward location machine.
    2023-04-23 09:15:03下载
    积分:1
  • Buzzer buzzer ring to change the frequency by changing the delay time if the buz...
    蜂鸣器响 改变蜂鸣器的频率,通过改变延时时间 蜂鸣器的时间要是是靠延时来完成的-Buzzer buzzer ring to change the frequency by changing the delay time if the buzzer is the time to be completed by the time delay
    2022-01-25 21:10:40下载
    积分:1
  • 端口控制发光二极管亮灭。 【硬件连接】通过SPCE061A的1位I/O端口(本例中使用IOA15端口),经一限流电阻后接一个发光二极管至地...
    端口控制发光二极管亮灭。 【硬件连接】通过SPCE061A的1位I/O端口(本例中使用IOA15端口),经一限流电阻后接一个发光二极管至地-Port control to eliminate bright light-emitting diodes. [] Through SPCE061A hardware connection of an I/O port (in this example, the use of IOA15 port), with a current limiting resistor followed by a light-emitting diodes to land
    2023-03-04 20:15:03下载
    积分:1
  • 696518资源总数
  • 104377会员总数
  • 20今日下载