-
failed to translate
增量式PIDc 语言下实现的例程.rar-failed to translate
- 2022-04-13 14:42:46下载
- 积分：1
-
51单片机学习原代码经验丰富工程师编写实际运行通过
51单片机学习原代码经验丰富工程师编写实际运行通过-51 Single-chip learning the original source of experienced engineers to run through the preparation of the actual
- 2022-07-07 10:09:52下载
- 积分：1
-
一个用单片机开发的硬盘控制器,可以实现对大容量硬盘数据的读写!...
一个用单片机开发的硬盘控制器,可以实现对大容量硬盘数据的读写!-With the development of a single-chip hard disk controller, can realize the large capacity hard disk data read and write!
- 2022-01-24 15:09:16下载
- 积分：1
-
W3100是WIZnet公司专门为以太网互联和嵌入式设备推出的硬件TCP／IP协议栈芯片，其硬件TCP／IP协议栈包含了TCP、UDP、IP、ARP和ICMP协...
W3100是WIZnet公司专门为以太网互联和嵌入式设备推出的硬件TCP／IP协议栈芯片，其硬件TCP／IP协议栈包含了TCP、UDP、IP、ARP和ICMP协议，这是他的indirect模式的原码-WIZnet W3100 is designed for the Internet and Embedded Ethernet equipment introduced hardware TCP/IP protocol stack chips, and hardware TCP/IP protocol stack includes TCP, UDP, IP, ICMP and ARP agreement, it is his indirect model of the original code
- 2022-08-09 10:14:34下载
- 积分：1
-
2个F040之间的CAN通讯，可以远程帧收发，c语言
2个F040之间的CAN通讯，可以远程帧收发，c语言-2 of the CAN communication between the F040, you can send and receive remote frames, c language
- 2022-01-26 05:51:08下载
- 积分：1
-
包括电路图和源程序，汇编语言编写。JP1、JP2、JP3为电机接口，JP5为投币器接口，JP4为指示灯接口...
包括电路图和源程序，汇编语言编写。JP1、JP2、JP3为电机接口，JP5为投币器接口，JP4为指示灯接口-including circuit diagrams and source code, written in assembly language. JP1, JP2, JP3 for electrical interfaces, JP5 for the coin interface, the interface indicator of JP4
- 2022-12-04 08:50:03下载
- 积分：1
-
51 Microcontroller Interface C source code with the 12864LCD
51单片机与12864LCD接口C源程序代码-51 Microcontroller Interface C source code with the 12864LCD
- 2022-06-27 05:47:50下载
- 积分：1
-
提供与C51程序设计的学习者，并加入这些网站，希望…
providing learners for programming with C51, and joining in these web,hopefully finding people with C51 programming so that it will can be studied each other.-providing learners for programming with C 51, and joining in these web, hopefully finding people with C51 programming so that it will can be studied each other.
- 2023-03-01 10:50:03下载
- 积分：1
-
* Hardware architecture: PA0
* 硬件结构： PA0-5对应６个ＬＥＤ数显管的位 ，PC0-7对应各ＬＥＤ数显管的段 ，PB4-7为键盘。
* 软件描述： 上电后，时钟从00.00.00（时/分/秒）自动走时，在走时状态时 ， 按PB4（设定
* 键）超过3秒可循环选择调整时间/工作参数 ，接着按PB5以确定选择的操作 ，进入调整操作后 ，
* 按PB5选择欲调整参数，按PB6（增加键）完成调整参数操作 。按PB7，进入时控运行，PB1亮，
* 再按PB7停止时控运行，回显走时。在定时到时，PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard.
* Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis
* The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation
* Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov
- 2022-04-16 19:29:12下载
- 积分：1
-
这是基于温度采集的报警系统 是利用MSP430 单片机实现控制
这是基于温度采集的报警系统 是利用MSP430 单片机实现控制-This based on the collection of temperature alarm system is the use of MSP430 MCU control
- 2023-01-01 03:00:03下载
- 积分：1
