c语言实现c51单片机PWM输出控制电机的转角-c51

单片机c语言源程序 初学者 很有用哦 -SCM c language source code is useful for beginners oh

CC2430 DMA程序 CC2430 DMA程序 CC2430 DMA程序-CC2430 DMA process procedures CC2430 DMA procedures CC2430 DMA procedures CC2430 DMA

如何在硬件条件允许的情况下在C语言中使用双数据指针提高程序的执行效率,文章还给出了例子程序.-How to hardware conditions permit in the C language using a dual data pointers improve efficiency in the implementation process, the article also gives examples of the procedure.

78EXXPCB11 winbond51单片机源码一堆-78EXXPCB11 winbond51 SCM source heap

最高实时取样率2M点/秒，精度8Bit 取样缓冲器深度：256字节 模拟频带宽度 0 - 1MHz 垂直灵敏度100mV/Div - 5V/Div (按1-2-5 方式递进)-2M real-time sampling rate of the highest points/sec, accuracy of sampling 8Bit buffer depth: 256 bytes bandwidth analog 0- 1MHz vertical sensitivity 100mV/Div- 5V/Div (by way of progressive 1-2-5)

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta

motorola 1.4" CSTN LCD test program. Drive IC: SSD17-1.4 "CSTN LCD test program. Drive IC : SSD17

在Windows环境下应用VC++实现PC机与单片机的几种串行通信方法，给出了用Visual C++6.0编写的PC机程序和用C51编写的单片机通信程序。经实际应用系统运行稳定可靠。-In the Windows environment application VC++ Realize PC machine with several single-chip serial communication method using Visual C++ 6.0 prepared PC-preparation procedures and the use of C51 microcontroller communication program. Through the practical application of system operation is stable and reliable.

利用P89C66X系列单片机实现I2C总线主器件函数操作库-use P89C66X Series MCU I2C bus owners to operate the device function