-
用MCS51系列单片机开发的交通灯控制程序
用MCS51系列单片机开发的交通灯控制程序-MCS51 series single-chip with the development of the traffic lights control procedures
- 2022-11-21 14:50:03下载
- 积分：1
-
本程序是C语言编写的,由 步进电机驱动的指针式温度表,反应灵敏,指示精确....
本程序是C语言编写的,由 步进电机驱动的指针式温度表,反应灵敏,指示精确.-this process is the preparation of the C language from the stepper motor-driven pointer thermometer responsive, precise instructions.
- 2023-04-04 04:40:03下载
- 积分：1
-
使用cnpic18f452的MS320240Bled初始化，使用PIC_CCS编译
使用cnpic18f452的MS320240Bled初始化，使用PIC_CCS编译-MS320240Bled use of cnpic18f452 initialization, use the compiler PIC_CCS
- 2022-02-28 09:07:44下载
- 积分：1
-
Sl811 increase the use of single
利用单片机arm加sl811芯片实现对u盘读写的控制，代码仅供大家参考，如有不对之处，敬请谅解-Sl811 increase the use of single-chip chip arm of the u disk read and write control code for your reference, if doing so after updating
- 2022-03-17 18:22:58下载
- 积分：1
-
CAN通讯 有源程序 很好 大家来看看 SJA1
CAN通讯 有源程序 很好 大家来看看 SJA1-CAN communications have a very good source to look at the U.S. SJA1
- 2022-02-01 02:22:54下载
- 积分：1
-
Library CH375. Communications, as well as for the usb disk to read and write u a...
CH375的库。用于usb通信以及u盘读写的一块好芯片。-Library CH375. Communications, as well as for the usb disk to read and write u a good chip.
- 2023-01-04 16:25:03下载
- 积分：1
-
[第1章]SPCE061A 硬体结构介绍
[第2章]指令系统
[第3章]u’nSP IDE 工具介绍
[第4章]SPCE061A各功能举例介绍...
[第1章]SPCE061A 硬体结构介绍
[第2章]指令系统
[第3章]u’nSP IDE 工具介绍
[第4章]SPCE061A各功能举例介绍
[第5章]语音处理应用介绍
[第6章]语音压缩工具
[第7章] 61板介绍
全部都是PPT-[Chapter 1] SPCE061A hardware structure Introduction [Chapter 2] instruction [Chapter 3] u nSP IDE tools Introduction [Chapter 4] SPCE061A introduce the function, for example [Chapter 5] introduce voice processing applications [Chapter 6 ] voice compression tools [Chapter 7] 61 plate introduce all PPT
- 2023-04-21 13:15:07下载
- 积分：1
-
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序,...
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.
- 2023-08-01 05:40:03下载
- 积分：1
-
2051由1Hz的频率测试到1M测试C程序
用2051制作的测试1HZ到1M的频率测试C程序 -2051 produced by the test frequency of 1Hz to 1M test C program
- 2022-03-20 23:04:20下载
- 积分：1
-
基于1698的160×160的液晶驱动程序
基于1698的160×160的液晶驱动程序-Based on 1698
- 2023-05-20 23:25:03下载
- 积分：1
