登录
首页 » IAR » 飞思卡尔平衡光电

飞思卡尔平衡光电

于 2022-08-17 发布 文件大小:7.26 kB
0 113
下载积分: 2 下载次数: 1

代码说明:

第八届飞思卡尔智能车竞赛平衡光电    MC9S12XS128的  网上找的  部分程序  区赛二等奖   同学参考的  用起来挺不错的   参数要自己调

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 2个ZigBee节点组网项目 (拓展)
    说明:  使用2个ZigBee节点组网,A做协调器,B做终端节点,PC机通过串口连接A,A协调器通过串口(发送命令)操控B终端节点写入和读取NV数据,NV数据为B终端节点指示灯的闪烁的时间间隔。(Two ZigBee nodes are used to form a network, A is used as coordinator, B is used as terminal node, PC is connected to A through serial port, A coordinator controls B terminal node to write and read NV data through serial port (sending commands). NV data is the flashing time interval of B terminal node indicator.)
    2020-06-23 06:40:01下载
    积分:1
  • Sx1208底层驱动程序
    The SX1208 is a highly integrated RF transceiver capable of operation from 290MHz to 510MHz, including the 315 and 434 MHz license-free ISM (Industry Scientific and Medical) frequency bands. Its highly integrated architecture allows for a minimum of external components whilst maintaining maximum design flexibility. All major RF communication parameters are programmable and most of them can be dynamically set. The SX1208 offers the unique advantage of programmable narrow-band and wide-band communication modes without the need to modify external components. The SX1208 is optimized for low power consumption while offering high RF output power and channelized operation. TrueRF™ technology enables a lowcost external component count (elimination of the SAW filter) whilst still satisfying ETSI and FCC regulations.
    2022-05-20 08:11:51下载
    积分:1
  • Mifare ultralight reader on STM8S003 mcu
    基于STM8S003的Mifare超轻阅读器mcu.设备读取卡序列号,在EEPROM中搜索,如果存在,则在几秒钟内打开输出(漏极开路)。每个读卡的序列号通过RS-485相互传输设备。支持具有7字节序列号的Mifare经典卡透镜编程EEPROM中的卡在万事达卡。第一设备首次通电(或清除EEPROM)后读取的卡为MasterCard(万事达卡)。EEPROM可通过拔下的针脚19清除STM8S003 mcu在设备通电时接地向上。核心:STM8S003;输出1:opendrain;输出2:RS-485(卡上传输的7字节SN)。存档包含:STM8S003(IAR、C、assembler)的源代码;原理图和PCB板项目(PCAD2002)。
    2022-06-19 09:39:58下载
    积分:1
  • 计算时钟神器
    for omapl 138 clock calculation
    2018-02-05 22:46:10下载
    积分:1
  • 蓝牙4.0 cc2540串口透传源码
    蓝牙4.0 cc2540串口透传源码 OSAL 1.3.2协议栈,BLE蓝牙4.0串口透传源码,测试过没有问题,只有这么多,不知道还有写什么,这样说明已经够清楚了吧!!!!!!!
    2022-02-15 08:59:29下载
    积分:1
  • 项目7 (拓展)-(我的电脑版)-成功
    使用2个ZigBee节点组网,A做协调器,B做终端节点,PC机通过串口连接A,A协调器通过串口(发送命令)操控B终端节点写入和读取NV数据,NV数据为B终端节点指示灯的闪烁的时间间隔。(Two ZigBee nodes are used to form a network, A is used as coordinator, B is used as terminal node, PC is connected to A through serial port, A coordinator controls B terminal node to write and read NV data through serial port (sending commands). NV data is the flashing time interval of B terminal node indicator.)
    2020-06-23 06:40:01下载
    积分:1
  • nrf24l01_avr
    nrf24l01的avr驱动, spi串口控制。(nrf24l01 avr driver, control with spi.)
    2018-03-14 09:05:30下载
    积分:1
  • SX1276点对点透传程序
    SX1276采用LORA调试方式可大大增加通信距离, 可广泛应用于各种场合的短距离物联网无线通信领域.本程序实现LoRa透传,验证可以使用。
    2022-12-22 15:15:03下载
    积分:1
  • 无线传感器实验
         CPU通过总线式温湿度传感器采集温度、湿度数据。CPU通过I/O口直接驱动蜂鸣器鸣叫,以及继电器吸合(继电器触点带动外围设备工作)。当温度、湿度超过给定阀值时,启动继电器(听到啪嗒的吸合声)并发出蜂鸣器报警。温室度参数定时发往到串口调试器以供查看,也可显示于自带的液晶屏上。 请点击左侧文件开始预览 !预览只提供20%的代码片段,完整代码需下载后查看 加载中 侵权举报
    2022-05-29 23:10:21下载
    积分:1
  • 项目5 (拓展)-(我的电脑版)-成功
    协调器和终端节点通过串口连接PC机,相互通讯,串口助手上可以显示(Coordinator and terminal node connect PC through serial port, communicate with each other, and can be displayed on serial assistant.)
    2020-06-23 06:20:02下载
    积分:1
  • 696524资源总数
  • 103938会员总数
  • 55今日下载