-
这是一个关于串口通信的程序，是用C
语言和汇编编写的，适合大多同学。...
这是一个关于串口通信的程序，是用C
语言和汇编编写的，适合大多同学。-This is a serial communication about the procedure is written in C and assembly language for most students.
- 2022-04-22 17:53:20下载
- 积分：1
-
12232液晶屏
12232液晶屏->正文 [电子信息]:12232液晶屏 产品名称: 12232液晶屏 电话:86-755-...12232点阵,外型尺寸66*29mm,STN黄绿模-12,232 LCD-
- 2022-01-27 12:41:34下载
- 积分：1
-
keil
- 2022-05-05 05:14:40下载
- 积分：1
-
红外ICCAVR下的译码程序，包括所有源代码，以及…
ICCAVR下的红外解码程序，包括全部源码，还有原理图和PCB图，以及主要芯片资料-Under the infrared ICCAVR decoding procedures, including all source code, as well as PCB schematics and maps, as well as major chipset information
- 2022-03-24 17:15:39下载
- 积分：1
-
开发流程
开发流程-Development process
- 2023-04-12 05:45:03下载
- 积分：1
-
一个时钟发生的小例子，希望能对大家有帮助
一个时钟发生的小例子，希望能对大家有帮助-Occurred in a small example of the clock, hoping to have everyone help
- 2022-07-15 19:13:53下载
- 积分：1
-
l298调 速 程 序 常规的接法是这样的，EnableA接PWM信号，Input1输入正反控制信号， Input2是Input1经过反相以后的信号。L298的...
l298调 速 程 序 常规的接法是这样的，EnableA接PWM信号，Input1输入正反控制信号， Input2是Input1经过反相以后的信号。L298的电平是与TTL电路相兼容的，一般是超过2.5V就为高电平。假如Input1为高电平时电机正转，那么低电平时就是反转，PWM信号控制电机的转速。
_________________
-l298 procedures conventional speed connection that is the case, EnableA then PWM signal, Input1 input positive and negative control signals, Input2 is Input1 through after RP signal. L298 level is compatible with TTL circuits, and is generally more than 2.5V for the high. If Input1 is high when the motor is transferred, then that is when low-level inversion, PWM signal to control motor speed. _________________
- 2022-06-18 18:51:26下载
- 积分：1
-
德州仪器公司推出的ADS7870型低功耗数据采集器件的ARM控制源程序...
德州仪器公司推出的ADS7870型低功耗数据采集器件的ARM控制源程序-Texas Instruments Introduces ADS7870 type of low-power data acquisition devices ARM control source
- 2022-05-14 07:47:55下载
- 积分：1
-
PIC24单片机程序示例。
目前这方面的资料较少。自己先顶一下。...
PIC24单片机程序示例。
目前这方面的资料较少。自己先顶一下。-PIC24 Singlechip sample procedures. At present, less information in this regard. Their first top-click.
- 2022-01-24 09:44:10下载
- 积分：1
-
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序,...
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.
- 2023-08-01 05:40:03下载
- 积分：1
