-
7279的C代码.可在KEIL的环境任意移植.
7279的C代码.可在KEIL的环境任意移植.-7279 C code. In KEIL environment arbitrary transplant.
- 2022-05-18 05:04:20下载
- 积分：1
-
- 2022-03-11 22:20:52下载
- 积分：1
-
LPC932 Singlechip NXP51 based on the design of the electronic clock (TOWIN compa...
基于NXP51单片机LPC932电子时钟的设计（致远公司学生用开发板）-LPC932 Singlechip NXP51 based on the design of the electronic clock (TOWIN company for student development board)
- 2023-07-21 23:50:04下载
- 积分：1
-
51单片机的4层电梯控制源代码，有需要的可以参考一下
51单片机的4层电梯控制源代码，有需要的可以参考一下-51 SCM four-layer elevator control source code, there is a need that can refer to
- 2023-02-09 23:55:04下载
- 积分：1
-
RJ45连接器包Protel PCB库
RJ45接头的Protel PCB封装库-RJ45 connectors package Protel PCB Library
- 2022-02-04 01:37:05下载
- 积分：1
-
单片机子程序,C源代码,4X4矩阵键盘,KEIL C开发环境.
单片机子程序,C源代码,4X4矩阵键盘,KEIL C开发环境.-Singlechip subroutine, C source code, 4X4 matrix keyboard, KEIL C development environment.
- 2022-07-03 20:10:57下载
- 积分：1
-
红外遥控接收
ORG 0000H
LJMP START 转入主程序
ORG 0010H
START:
MAIN:
JNB P2...
红外遥控接收
ORG 0000H
LJMP START 转入主程序
ORG 0010H
START:
MAIN:
JNB P2.2,IR
LJMP MAIN
以下为进入P3.2脚外部中断子程序，也就是解码程序
IR:
MOV R6,#9
SB:
ACALL DELAY882 调用882微秒延时子程序
JB P2.2,EXIT 延时882微秒后判断P3.2脚是否出现高电平如果有就退出解码程序
DJNZ R6, SB 重复10次，目的是检测在8820微秒内如果出现高电-infrared remote control receiver ORG 0000H LJMP START into main program ORG 0010H START : MAIN : JNB P2.2, IR LJMP MAIN below to enter P3.2 foot external interrupt subroutine, which is decoding procedures IR : MOV R6, SB# 9 : Calling ACALL DELAY882 882 microsecond delay subroutine JB P2.2, EXIT 882 microsecond delay after the judgment whether there P3.2 feet to I quit if decoding procedures DJNZ R6, SB repeated 10 times, the purpose is to test if within 8,820 microsecond high
- 2022-07-21 10:12:11下载
- 积分：1
-
本设计以P89V51RD2FN单片机为电动小车的控制核心，采用MSA
本设计以P89V51RD2FN单片机为电动小车的控制核心，采用MSA-LD2.0倾角传感器实时测量跷跷板的倾斜角，用ST198光电传感器检测黑色引导线监测小车运动。光电传感器和倾角传感器模块把实时测量信号馈送至单片机，利用专用细分芯片TA8435H驱动步进电机，以脉宽调制式斩波方式对步进电机步进角进行细分，控制和调节小车速度。采用增量式PID控制算法确保小车能够达到平衡；用RT128×64M液晶显示时间、角度等参数。经测试表明：小车各项性能指标达到设计要求，能够实现30秒内小车行驶到规定点，并保持跷跷板平衡；在跷跷板一端配重可调整的情况下，小车也能自动找到平衡点并保持跷跷板平衡。-The single-chip design for the electric car P89V51RD2FN control of the core, the MSA-LD2.0 seesaw angle sensor real-time measurement of the tilt angle, the detection of black ST198 photoelectric sensor to monitor vehicle movement and guide lines.Photoelectric sensors and angle sensors in real-time measurement module to feed the signal to the microcontroller, using a dedicated sub-chip stepper motor driver TA8435H to PWM chopper-type stepper motor on the sub-stepping angle, control and regulation vehicle speed. The use of incremental PID control algorithm to ensure that the car can achieve balance with LCD RT128 × 64M time, angle and other parameters.After the test showed that: the performance car
- 2023-09-02 02:10:04下载
- 积分：1
-
I tested the LCD driver compilation procedures, applicable to all non
我测试通过的液晶驱动汇编程序,适用于所有不带字库的液晶,如CA12864A-I tested the LCD driver compilation procedures, applicable to all non-character LCD, as CA12864A
- 2022-07-07 07:16:35下载
- 积分：1
-
PCF8563 的驱动程序，用两个普通的IO口模拟I2C总线，包括100KHZ（T=10US）的标准模式选择和400KHZ的快速模式选择，默认11.0592MH...
PCF8563 的驱动程序，用两个普通的IO口模拟I2C总线，包括100KHZ（T=10US）的标准模式选择和400KHZ的快速模式选择，默认11.0592MHZ的晶振-PCF8563 of the driver, with two ordinary analog IO I2C bus, including the extremely low distortion (T = 10US), the standard model selection and 400KHZ fast mode selection, the crystal default 11.0592MHZ
- 2023-08-11 19:20:03下载
- 积分：1
