登录
首页 » SCM » microsteeeper mega48的步进电机

microsteeeper mega48的步进电机

于 2022-05-31 发布 文件大小:23.15 kB
0 59
下载积分: 2 下载次数: 1

代码说明:

基于mega48单片机的步进电机分割程序mega48

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • AD 转换 用定时器中断 显示 0
    AD 转换 用定时器中断 显示 0--5V-AD0804 zhongduan xianshi
    2022-01-25 19:06:06下载
    积分:1
  • 汉字液晶显示LCM 160X2的控制源程序,针对各种PIC单片机。也可对其它单片机参考...
    汉字液晶显示LCM 160X2的控制源程序,针对各种PIC单片机。也可对其它单片机参考-Chinese character LCD LCM 160X2 source control, targeting a variety of PIC. It can reference other MCU
    2022-05-20 04:15:39下载
    积分:1
  • 本程序运行于C8051F330,功能为接收遥控器发出的红外信号,然后等待上位机通过I2C总线来读取。IR数据接收完毕后,不再采集新的IR数据,一直等待上位机将数...
    本程序运行于C8051F330,功能为接收遥控器发出的红外信号,然后等待上位机通过I2C总线来读取。IR数据接收完毕后,不再采集新的IR数据,一直等待上位机将数据取走后才开始准备接收新的IR数据-this program running on the C8051F330, functional remote control device to receive the infrared signal, Then wait for the PC through the I2C bus to read. IR data receiving end, not the acquisition of new IR data have been waiting for the PC will be removed after data began preparing to receive the new IR data
    2023-08-26 01:10:03下载
    积分:1
  • c51编写的“贪吃蛇”
    c51编写的“贪吃蛇”-prepared by the "Snake"
    2023-04-07 09:40:02下载
    积分:1
  • 单片机动态内存分配代码,实现malloc.
    单片机动态内存分配代码,实现malloc.-Single-chip dynamic memory allocation code, realize malloc.
    2022-06-18 06:10:46下载
    积分:1
  • Week Ligong serial communications, with debugging software ... can refer to lear...
    周立功串口通讯,附调试软件...可以参考学习下.-Week Ligong serial communications, with debugging software ... can refer to learn under.
    2022-03-21 20:28:06下载
    积分:1
  • 三相步进电机的三相六拍工作方式,正转的绕组通电顺序:A、AB、B、BC、C、CA、A,反转的通电顺序:A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性,故步进电机的工作过程中不能及时的启动和停止,在启动时应慢慢的加速到预定速度,在停止前应逐渐减速到停止,否则,将产生失步现象。 步进电机的控制问题可总结为两点: 1、产生工作方式需要的时序脉冲; 2、控制步进电机的速度,使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.
    2022-07-20 15:21:46下载
    积分:1
  • SENSE of a temperature transmitter Hart PC interface, and switching functions in...
    SENSE 的一款Hart温度变送器的上位机操作界面,有中英文切换的功能,做Hart仪表的可以参考哦-SENSE of a temperature transmitter Hart PC interface, and switching functions in both English and Chinese, make Hart instrument can refer Oh
    2022-02-24 15:51:19下载
    积分:1
  • 51――14
    51――14-单线温度传感器18b20;用温度传感器18b20检测温度-51- 14- single-temperature sensor 18b20 Detect 18b20 temperature sensor with temperature
    2023-01-20 15:45:04下载
    积分:1
  • libfetion 用于pidex的飞信控件
    libfetion 用于pidex的飞信控件-libfetion for the pidex Fetion controls
    2022-03-01 02:27:15下载
    积分:1
  • 696521资源总数
  • 104077会员总数
  • 0今日下载