-
基于MSP430的I2C驱动程序，超强可移植性，方便重定义管脚
基于MSP430的I2C驱动程序，超强可移植性，方便重定义管脚-MSP430 Based on the I2C driver, super-portable, convenient re-definition of pin
- 2023-05-27 12:00:02下载
- 积分：1
-
A/转换程序，用在8051或8031，此外还有两个小的显示的程序
A/转换程序，用在8051或8031，此外还有两个小的显示的程序-A/switching procedures used in 8051 or 8031, in addition to two small display procedures
- 2022-03-07 07:14:54下载
- 积分：1
-
基于TI的MSP430的方面的相关的软件和MSP430的相关的资料.
基于TI的MSP430的方面的相关的软件和MSP430的相关的资料.-based on TI"s MSP430 aspects of the software and MSP430 relevant information.
- 2022-01-25 21:28:08下载
- 积分：1
-
Keil C51 uses the detailed solution
Keil C51使用详解-Keil C51 uses the detailed solution
- 2022-08-31 14:55:04下载
- 积分：1
-
交通灯控制系统，可灵活设置多路时间
交通灯控制系统，可灵活设置多路时间-Traffic light control system, can be flexibly set up multi-channel time
- 2022-06-18 07:19:04下载
- 积分：1
-
串口通讯的XModem协议源码，有兴趣的朋友可以参考！
串口通讯的XModem协议源码，有兴趣的朋友可以参考！-serial communications IEEE-source agreement, interested can refer friends!
- 2022-02-01 23:37:08下载
- 积分：1
-
三菱16
三菱16位单片机M306N0系列，I2C驱动。-Mitsubishi 16-bit microcontroller M306N0 series, I2C driver.
- 2022-05-13 01:20:56下载
- 积分：1
-
At can be given its arguments in a file. You can comment
out lines by precedin...
At can be given its arguments in a file. You can comment
out lines by preceding them with either # or -
characters. This is an easy way to temporarily disable
some commands.
The CONTINUE-command is most useful at the end of the
file. When this command is read, the file is started
again from the beginning. You can use it situations where
the machine is not shut down for the night and you want
to run some commands every day.- At can be given its arguments in a file. You can comment
out lines by preceding them with either# or-
characters. This is an easy way to temporarily disable
some commands.
The CONTINUE-command is most useful at the end of the
file. When this command is read, the file is started
again from the beginning. You can use it situations where
the machine is not shut down for the night and you want
to run some commands every day.
- 2022-02-21 09:29:04下载
- 积分：1
-
51单片机控制的红外遥控的接收部分的程序，可实现解调、解码和现实的功能，很实用！...
51单片机控制的红外遥控的接收部分的程序，可实现解调、解码和现实的功能，很实用！-51 MCU controlled by infrared remote control receiver part of the process, can be realized demodulation, decoding and realistic features, very practical!
- 2022-02-02 22:15:51下载
- 积分：1
-
本程序用于MICROCHIP 24LC64 EEPROM的读写。本程序不使用芯片级联方式，
请将A0，A1，A2 管脚接至低电平。本程序使用IOC6作为SD...
本程序用于MICROCHIP 24LC64 EEPROM的读写。本程序不使用芯片级联方式，
请将A0，A1，A2 管脚接至低电平。本程序使用IOC6作为SDA，IOC7作为SCL。
程序中的地址空间最大可至64K：24LC00-16-0，24LC01-128-8，24LC02-256-8，
24LC04-512-16，24LC08-1K-16，24LC16-2K-32，24LC32-4K-32，24LC64-8K-32，
24LC128-16K-64，24LC256-32K-64，24LC512-64K-128，读写数据均为8bits。
以上器件的格式为（型号-地址空间-页大小）不同器件的页大小不同，因此页写
程序需作相应修改，其他字节写，随机读以及顺序读程序均相同-This procedure for the MICROCHIP 24LC64 EEPROM read and write. This procedure does not use chips cascade way, please A0, A1, A2 pin to low level access. This procedure used IOC6 as SDA, IOC7 as SCL. Process address space available to the largest 64K: 24LC00-16-0, 24LC01-128-8, 24LC02-256-8, 24LC04-512-16, 24LC08-1K-16, 24LC16-2K-32, 24LC32-4K- 32,24 LC64-8K-32, 24LC128-16K-64, 24LC256-32K-64, 24LC512-64K-128, read and write data are 8bits. The format for the above device (Model- address space- page size) of different devices of different sizes of pages, so page written procedures need to be amended accordingly, and other bytes to write, rand
- 2022-07-12 21:23:12下载
- 积分：1
