-
- 2022-01-24 19:02:01下载
- 积分:1
-
在c51下液晶显示块LCD20040411的编程实例。
在c51下液晶显示块LCD20040411的编程实例。-Under the liquid crystal display in the C51 block LCD20040411 programming examples.
- 2022-03-19 18:41:02下载
- 积分:1
-
9320 drvice code
9320 drvice code -9320 drvice code
- 2022-12-24 15:15:04下载
- 积分:1
-
Luminary看门狗代码(IAR开发环境)
LUMINARY 看门狗代码(IAR开发环境)-Luminary watchdog code (IAR development environment)
- 2022-01-30 16:27:03下载
- 积分:1
-
用C实现信号发生装置:1、正弦波:频率、幅度可调。
2、三角波:频率、幅度可调。
3、方 波:频率、幅度、占空比可调。
4、按键:波形切换、频率调节...
用C实现信号发生装置:1、正弦波:频率、幅度可调。
2、三角波:频率、幅度可调。
3、方 波:频率、幅度、占空比可调。
4、按键:波形切换、频率调节、幅度调节、方波占空比调节。
5、显示:信号的频率、幅度,在方波时还要显示占空比。
-Implementation using C Signal: 1, sine wave: frequency, amplitude adjustable. 2, triangle-wave: frequency, amplitude adjustable. 3, square wave: the frequency, amplitude, duty cycle adjustable. 4, button: switch waveform, frequency regulation, rate regulation, adjust the duty cycle square wave. 5, show that: the signal frequency, amplitude, when they showed at the duty cycle square wave.
- 2022-02-04 23:43:04下载
- 积分:1
-
led source programs, and 51 are negative then led to, and then compile led.asm s...
led源程序,51负则led,然后编译发光二极管.asm摊位,本来会领一个走出黑暗的结果
- 2022-01-26 04:54:31下载
- 积分:1
-
LED显示面板,基于CAN网络控制的,多主结构
LED显示面板,基于CAN网络控制的,多主结构-LED display panel, based on the CAN network-controlled, multi-master structure
- 2022-05-24 06:00:18下载
- 积分:1
-
这是在台湾kingb 8
这是用台湾KingB 8位单片机开发的科学计算器程序,有一定的参考价值-This is used in Taiwan KingB 8-bit single chip scientific calculator developed procedures have certain reference value
- 2022-03-17 03:40:27下载
- 积分:1
-
At can be given its arguments in a file. You can comment
out lines by precedin...
At can be given its arguments in a file. You can comment
out lines by preceding them with either # or -
characters. This is an easy way to temporarily disable
some commands.
The CONTINUE-command is most useful at the end of the
file. When this command is read, the file is started
again from the beginning. You can use it situations where
the machine is not shut down for the night and you want
to run some commands every day.- At can be given its arguments in a file. You can comment
out lines by preceding them with either# or-
characters. This is an easy way to temporarily disable
some commands.
The CONTINUE-command is most useful at the end of the
file. When this command is read, the file is started
again from the beginning. You can use it situations where
the machine is not shut down for the night and you want
to run some commands every day.
- 2022-02-21 09:29:04下载
- 积分:1
-
avr与PC的USB通讯(D12.rar
avr与PC的USB通讯(D12.rar-avr PC with the USB communications (D12.rar
- 2022-12-16 03:10:03下载
- 积分:1