-
是一个G代码转换的源程序,将标准G代码读入后在UG环境下生成加工代码刀具路径。...
是一个G代码转换的源程序,将标准G代码读入后在UG环境下生成加工代码刀具路径。-G is a conversion of source code, to reduce the standard G code read in the UG environment processing code generated tool paths.
- 2022-04-28 18:09:50下载
- 积分:1
-
03年全国大学生电子设计竞赛智能小车mega16源代码
03年全国大学生电子设计竞赛智能小车mega16源代码-2003 National Undergraduate Electronic Design Contest smart car mega16 source code
- 2022-02-02 04:48:25下载
- 积分:1
-
利用Proteus仿真RS232串行通讯口,串口助手…
使用PROTEUS仿真的RS232串行通信口,可在串口助手输入,激活7段数码管显示相应的数字-PROTEUS simulation using RS232 serial communication port, serial port assistant in the input, activation of 7 digital tube display the corresponding figure
- 2022-03-09 16:53:22下载
- 积分:1
-
这是一个开发基于STC89C58 51样品在Keil拼音输入方法。
这是一个基于STC89C58开发的用于51上的拼音输入法示例KEIL工程,程序很好用,已经测试通过并已应用于实际当中-This is a development based on STC89C58 for 51 on the sample KEIL Pinyin input method works very well with the procedure has been tested and has been used in practice
- 2023-05-01 06:10:02下载
- 积分:1
-
1024fft用MSP430设计的音频信号分析仪
1024fft用MSP430设计的音频信号分析仪-1024fft design using MSP430 audio signal analyzer
- 2022-03-19 16:08:37下载
- 积分:1
-
CY7C68013的GPIF burst源程序,主要示例GPIF BURST模式的使用,编译环境为KEIL...
CY7C68013的GPIF burst源程序,主要示例GPIF BURST模式的使用,编译环境为KEIL-CY7C68013 the GPIF burst source, the main examples GPIF BURST model used to build environment KEIL
- 2023-06-21 22:25:03下载
- 积分:1
-
是一个利用单片机C语言生成各阶M序列的程序,还有发送程序
是一个利用单片机C语言生成各阶M序列的程序,还有发送程序-SCM is a C language generation of the M-series of procedures, there is this procedure
- 2022-02-16 03:25:28下载
- 积分:1
-
开发环境ICC
AVR单片机
用ADC做电压表 (多通道)
开发环境ICC
AVR单片机
用ADC做电压表 (多通道)
- 2022-03-28 15:24:52下载
- 积分:1
-
usb开发工具周立功公司下载很好用的一个软件
usb开发工具周立功公司下载很好用的一个软件-development tools usb Ligong weeks to download a very good company with a software
- 2022-01-22 08:33:24下载
- 积分:1
-
这是一个比较典型的PID处理程序,在使用单片机作为控制cpu时,请稍作简化,具体的PID 参数必须由具体对象通过实验确定。由于单片机的处理速度和ram资源的限制...
这是一个比较典型的PID处理程序,在使用单片机作为控制cpu时,请稍作简化,具体的PID 参数必须由具体对象通过实验确定。由于单片机的处理速度和ram资源的限制,一般不采用浮点数运算,而将所有参数全部用整数,运算 到最后再除以一个2的N次方数据(相当于移位),作类似定点数运算,可大大提高运算速度,根据控制精度的不同要求,当精度要求很 高时,注意保留移位引起的“余数”,做好余数补偿。这个程序只是一般常用pid算法的基本架构,没有包含输入输出处理部分。-This is a typical PID process, as in the use of SCM control cpu, please slightly simplified, specific PID parameters to be specific targets identified by experiments. As SCM processing speed and ram resource constraints, generally do not use floating-point operations, and will use all the parameters of all integers, and the final calculations to divide one of the Nth 2 data (the equivalent displacement), will count for a similar operation, it will greatly increase the computing speed, control Accuracy of different requirements and high precision, displacement caused reservations to the attention of the "I", which I do several compensation. This procedure is commonly used algorithm pid the basic structure does not include input and output processing.
- 2022-03-19 08:10:44下载
- 积分:1