-
Arm指令的全中文资料
Arm指令的全中文资料-Arm-wide directive Chinese data
- 2022-02-01 14:59:23下载
- 积分：1
-
有规律的点亮LED
单片机开发，用单片机控制板子上的LED灯，实现有规律的LED灯点亮，实现节日彩灯等画面，很好啊
- 2022-05-19 07:59:31下载
- 积分：1
-
ARM汇编指令集,全，容易理解，条理清晰
ARM汇编指令集,全，容易理解，条理清晰-ARM instruction set to compile the whole, easy to understand, the clarity of
- 2023-08-20 12:10:04下载
- 积分：1
-
SysTick_ARM
此示例演示如何配置 SysTick 以生成基本等于 1 女士的系统时钟设置为 168 MHz，SysTick 计时由 AHB clockHCLK 的时间。"延迟"功能实现基于 SysTick 结尾的计数事件。四个指示灯切换时间由延迟函数定义。
- 2023-06-28 20:55:03下载
- 积分：1
-
JIYU AT91SAM7X256的 + 12864点阵液晶屏的完整的驱动代码实现
JIYU AT91SAM7X256的 + 12864点阵液晶屏的完整的驱动代码实现-JIYU AT91SAM7X256 of+ 12864 dot matrix LCD driver code for the complete realization of
- 2022-01-21 18:07:38下载
- 积分：1
-
his project was built and tested with WinAVR
his project was built and tested with WinAVR-20060125.
Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!!
To build the code, just install WinAVR and run "make" from the console in echomaster and
echoslave subdirs.
"make program" will program the device if you have a AVRISP attached.
Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock
from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST!
Otherwise you wont get any clock signal to the AVR and then you can t program it or reset
the fuses!
The MC1319x has default clock output of 32kHz so you will have to set your programmer to
a very low frequency (
- 2023-02-22 21:55:03下载
- 积分：1
-
利用AIC计算，辨识模型，计算模型的p、q和φ参数值，然后进行用ARMA模型预测
%第一步，通过差分来获得静态数据。利用积分进行还原。
%在线利用AIC计算，辨识模型，计算模型的p、q和φ参数值，然后进行预测
确定模型为ARMA（p,q)，同时求自回归系数和移动平均系数
- 2022-02-10 17:14:49下载
- 积分：1
-
The document is based on Samsung 44b0 chip embedded systems arm of the mouth rtl...
该文件是基于三星44b0芯片arm嵌入式系统的rtl8019网口的驱动程序-The document is based on Samsung 44b0 chip embedded systems arm of the mouth rtl8019 Network Driver
- 2022-06-26 15:42:16下载
- 积分：1
-
DNW0.50A software source code, in the ARM2410 above the mouth through the serial...
DNW0.50A软件的源代码，在ARM2410上面通过串口和USB口烧写操作系统镜像时必须用到的软件。-DNW0.50A software source code, in the ARM2410 above the mouth through the serial port and USB programmer to be used for mirroring the operating system software.
- 2022-12-10 21:25:03下载
- 积分：1
-
LPC2368外部中断的程序。非常好，基于IAR的
LPC2368外部中断的程序。非常好，基于IAR的
- 2023-05-14 14:30:03下载
- 积分：1
