登录
首页 » SCM » 美国TI公司的protel 元器件库,在应用中需要更新,本人收集了最新的版本共30M,为提高上传速度分六次上传。文件名依次为TI_1到TI_6。希望大家设计电路...

美国TI公司的protel 元器件库,在应用中需要更新,本人收集了最新的版本共30M,为提高上传速度分六次上传。文件名依次为TI_1到TI_6。希望大家设计电路...

于 2022-02-13 发布 文件大小:1.28 MB
0 85
下载积分: 2 下载次数: 1

代码说明:

美国TI公司的protel 元器件库,在应用中需要更新,本人收集了最新的版本共30M,为提高上传速度分六次上传。文件名依次为TI_1到TI_6。希望大家设计电路板时少走弯路 以下是TI_5-TI" s U.S. Treasury protel components, need to be updated in the application, I collected a total of up-to-date version of 30M, to improve the upload speed upload six hours. File name followed by TI_1 to TI_6. Hope that the design of circuit board is less detours following TI_5

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 流水灯程序,实现8位数码管显示,动态组合显示
    流水灯程序,实现8位数码管显示,动态组合显示-Light water procedures, to achieve 8-bit digital tube display, the dynamic combination of show
    2022-03-10 15:11:16下载
    积分:1
  • software proteus 7.2 for design the circuit
    software proteus 7.2 for design the circuit
    2022-03-12 10:05:46下载
    积分:1
  • * Hardware architecture: PA0
    * 硬件结构: PA0-5对应6个LED数显管的位 ,PC0-7对应各LED数显管的段 ,PB4-7为键盘。 * 软件描述: 上电后,时钟从00.00.00(时/分/秒)自动走时,在走时状态时 , 按PB4(设定 * 键)超过3秒可循环选择调整时间/工作参数 ,接着按PB5以确定选择的操作 ,进入调整操作后 , * 按PB5选择欲调整参数,按PB6(增加键)完成调整参数操作 。按PB7,进入时控运行,PB1亮, * 再按PB7停止时控运行,回显走时。在定时到时,PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov
    2022-04-16 19:29:12下载
    积分:1
  • on DDSAD9850 plans and procedures for the control procedures Serial MCU ADUC812
    关于DDSAD9850图和程序串口程序主控单片机ADUC812-on DDSAD9850 plans and procedures for the control procedures Serial MCU ADUC812
    2022-07-15 03:36:51下载
    积分:1
  • C8051F350单片机24位AD采样程序。
    C8051F350单片机24位AD采样程序。-C8051F350 single-chip 24-bit AD sampling procedures.
    2022-01-26 08:28:49下载
    积分:1
  • SmartGen generated with a size of 256* 8 Synchronous FIFO, and sending data thro...
    用SmartGen生成一个256*8的大小同步FIFO,并通过串口发送数据初始化FIFO。然后,再通过串口返回到上位机的串口调试程序显示,确认数据是否正确。-SmartGen generated with a size of 256* 8 Synchronous FIFO, and sending data through the serial port to initialize FIFO. And then back through the serial port to the PC serial port debugger display to confirm the data is correct.
    2022-03-03 12:50:01下载
    积分:1
  • 多功能电子钟、Proteus、源代码、原理图
    多功能电子钟、Proteus、源代码、原理图-Multi-functional electronic bell, Proteus, source code, schematics
    2022-01-31 12:57:54下载
    积分:1
  • 这个做了一个可以随着曲线而移动得小球,很好玩,大家看看是怎么随曲线移动得...
    这个做了一个可以随着曲线而移动得小球,很好玩,大家看看是怎么随曲线移动得-This can make a curve and move with a small ball, is a lot of fun, let us look at how the Mobile curve with a
    2023-02-17 16:45:04下载
    积分:1
  • 显示界面的显示程序显示 界面的显示程序
    显示界面的显示程序显示 界面的显示程序-Show interface show interface display program to display the show interface display program
    2022-04-21 20:06:46下载
    积分:1
  • Keyboard scanner, avr Singlechip mega16L control with double LCD screen, LCD dri...
    键盘扫描程序,avr单片机mega16L用双键控制液晶屏,液晶屏的驱动程序,我会在以后继续上传 -Keyboard scanner, avr Singlechip mega16L control with double LCD screen, LCD driver, I will continue to upload at a later
    2023-01-30 12:20:04下载
    积分:1
  • 696518资源总数
  • 104353会员总数
  • 66今日下载