-
AD转换器AD7890驱动程序（KeilC51）
AD转换器AD7890驱动程序（KeilC51）-AD converters AD7890 driver (KeilC51)
- 2022-03-19 21:13:13下载
- 积分：1
-
用89S51做的红外编码解码程序。载波用555做
用89S51做的红外编码解码程序。载波用555做-89S51 do with the infrared codec procedures. Carrier to do with 555
- 2023-04-25 17:30:03下载
- 积分：1
-
键盘的驱动，c代码，给嵌入式用的，可以拿来自己研究用，比较不错。大家多交流...
键盘的驱动，c代码，给嵌入式用的，可以拿来自己研究用，比较不错。大家多交流-Keyboard driver, c code for embedded use, and can use their own research, a good comparison. Members will exchange
- 2022-04-17 11:22:32下载
- 积分：1
-
C51源程序库（超过20）
C51源程序库（二十多个）-C51 source library (over 20)
- 2022-06-01 08:08:01下载
- 积分：1
-
cp210x非标波特率设置工具 CP210x Baud Rate Configuration Utility v1.0 Release Notes Copyri...
cp210x非标波特率设置工具 CP210x Baud Rate Configuration Utility v1.0 Release Notes Copyright (C) 2004 Silicon Laboratories, Inc. This release contains the following components: * CP210xBaudRateAliasConfig.exe * CP210xManufacturing.DLL * CP210xBaudRateAliasConfig VC++ project * REL_NOTES.TXT (this file) -cp210x non-standard baud rate configuration tool CP210x Baud Rate Configuration Utility v1.0 Release Notes Copyright (C) 2004 Silicon Laboratories, Inc.. This release contains the following components :* CP210xBaudRateAliasConfig.exe CP210xManufacturing.DLL*** CP210xBaudRateAliasConfig REL_NOTES VC project. TXT (this file)
- 2022-04-02 10:10:12下载
- 积分：1
-
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序,...
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.
- 2023-08-01 05:40:03下载
- 积分：1
-
AT91所有开发板的资料
AT91所有开发板的资料
AT91所有开发板的资料
AT91所有开发板的资料-porting all development board all the information porting Development Board of porting all of the information development board
- 2023-05-01 06:25:22下载
- 积分：1
-
Truly TSD4254 provided LCD liquid crystal display driver IC ST7549T initializati...
信利公司提供的TSD4254液晶LCD显示器的驱动芯片ST7549T的初始化程序-Truly TSD4254 provided LCD liquid crystal display driver IC ST7549T initialization procedure
- 2022-11-23 08:45:03下载
- 积分：1
-
QG8_demo学习板开发板例程
显示的例程，辛苦找来。
经过验证是正确的。...
QG8_demo学习板开发板例程
显示的例程，辛苦找来。
经过验证是正确的。-Board development board QG8_demo learning routine shown in routine, it is tough to get a large. Verified to be correct.
- 2022-05-30 09:27:37下载
- 积分：1
-
USB带宽测试的程序，针对CY7C68013的USB2.0接口芯片，编译环境为KEIL...
USB带宽测试的程序，针对CY7C68013的USB2.0接口芯片，编译环境为KEIL -USB bandwidth test procedures against CY7C68013 USB 2.0 interface chip, compile environment for KEIL
- 2022-05-27 16:33:34下载
- 积分：1
