-
Beizer曲线,用VC++编程的,可以调试一下试试看
Beizer曲线,用VC++编程的,可以调试一下试试看-Beizer curve, with VC++ Programming, you can debug you give it a try
- 2022-03-02 15:42:59下载
- 积分:1
-
一个分形程序,拥有图形界面,特别不同
一个分形程序,拥有图形界面,特别不同-a fractal procedures, with a graphical interface, in particular the different
- 2022-11-03 05:10:03下载
- 积分:1
-
vc++二维数据拟合源代码边干边学过后 共和国精华区 国会结构化...
vc++二维数据拟合源代码边干边学过后 共和国精华区 国会结构化-vc fitting two-dimensional data source learning by doing focus of the Republic after the structure of Congress
- 2022-04-21 17:10:24下载
- 积分:1
-
这是一个不规则窗体的事例,可以参考该程序来话不轨着窗体。...
这是一个不规则窗体的事例,可以参考该程序来话不轨着窗体。-This is an example of irregular form, can refer to the procedure to the form, then bad.
- 2022-04-21 16:25:39下载
- 积分:1
-
用vb6编写的可以拾取屏幕任意位置像素颜色的程序,同时可以得到一个圆形区域像素灰度的平均值...
用vb6编写的可以拾取屏幕任意位置像素颜色的程序,同时可以得到一个圆形区域像素灰度的平均值-Written by vb6 can pick up anywhere on the screen pixel color procedures, can be a circular area the average pixel gray scale, etc.
- 2022-03-09 15:40:36下载
- 积分:1
-
opengl太阳地球系统
基于openGL制作的太阳系模型。。。感觉还不错。。。。 -OpenGL-based models produced by the solar system. . . Feeling pretty good. . . .
- 2022-04-19 13:02:01下载
- 积分:1
-
bmp图像反色处理
bmp图像反色处理-bmp-color image processing
- 2022-11-11 11:40:03下载
- 积分:1
-
此程序段是采用局部模值最大法来进行边缘检测
此程序段是采用局部模值最大法来进行边缘检测-edge defect
- 2022-01-25 14:14:23下载
- 积分:1
-
用java做的一个立体正方形!可以通过键盘或鼠标实现左右上下移动;放大或缩小:
.doc 里面有运行通过的源码和截图~...
用java做的一个立体正方形!可以通过键盘或鼠标实现左右上下移动;放大或缩小:
.doc 里面有运行通过的源码和截图~-done with a three-dimensional square! Through the keyboard or mouse up and down about achieving; To zoom in and out : . doc inside running through the source code and screenshots ~
- 2022-01-26 01:53:34下载
- 积分:1
-
为了将零件固定在PCB上面,我们将它们的接脚直接焊在布线上。在最基本的PCB(单面板)上,零件都集中在其中一面,导线则都集中在另一面。这么一来我们就需要在板子上...
为了将零件固定在PCB上面,我们将它们的接脚直接焊在布线上。在最基本的PCB(单面板)上,零件都集中在其中一面,导线则都集中在另一面。这么一来我们就需要在板子上打洞,这样接脚才能穿过板子到另一面,所以零件的接脚是焊在另一面上的。因为如此,PCB的正反面分别被称为零件面(Component Side)与焊接面(Solder Side)。-parts to be fixed above the PCB, we will take their feet welded directly on the wiring. At its most basic PCB (single-panel), parts of which are concentrated in the side, wire were concentrated on the other side. Suppose we need burrows on the board, then through the legs of another plank, then parts of the legs is another welding in the face. Because of this, the PCB is negative components were known as surface (Component Side) and the welding surface (Solder Side).
- 2022-11-08 00:30:02下载
- 积分:1