登录
首页 » Arduino » PID

PID

于 2021-04-11 发布
0 164
下载积分: 1 下载次数: 0

代码说明:

说明:  一个简单的PID调试程序,具有可视化功能,输入初值和目标值可以实现可视化的计算过程(A simple PID debugging program, with visual function, input initial value and target value can realize visual calculation process)

文件列表:

2996831-456eadebf67b076e.png, 627278 , 2020-04-14
PID.ino, 1842 , 2019-08-02

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • STM32f107_PWM-2ch
    基于stm32f107vc的PWM 2路输出 控制电机 闭环调速 (Based stm32f107vc of PWM 2 output control loop speed control motor)
    2020-10-28 16:09:57下载
    积分:1
  • pc串口通信
    pc机串口通信,可以实现计算机与单片机,或者是两个单片机之间的通信(the communication through PC serial, between PC and SCM, or two SCM)
    2020-06-26 08:40:01下载
    积分:1
  • IIC
    IIC驱动,可以驱动所有IIC接口电路,并且高度模块化,提供接口,易于修改移植!!!(IIC drive which can drive any chip with iic)
    2020-06-20 09:20:01下载
    积分:1
  • FreeRTOS实验15-1 FreeRTOS软件定时器实验
    硬件资源: 1,DS0(连接在PA8),DS1(连接在PD2上) 2,串口1(波特率:115200,PA9/PA10连接在板载USB转串口芯片CH340上面) 3,ALIENTEK 2.8/3.5/4.3寸LCD模块(仅支持MCU屏) 4,按键KEY0(PC5)/KEY1(PA15)/KEY_UP(PA0,也称之为WK_UP) 实验现象: 通过按键KEY_UP可以控制定时器AutoReloadTimer_Handle的开启,这个是 周期定时器,一旦开启就会不断的运行,直到按下KEY1将其关闭。按下KEY0 可以打开定时器OneShotTimer_Handle,这是个单次定时器,只会运行一次, 运行周期到了以后就会停止运行,除非按下按键KEY0将其再次开启。(Hardware resources: 1, DS0 (connected to PA8), DS1 (connected to PD2) 2. Serial port 1 (baud rate: 115200, PA9/PA10 connected on board USB to serial chip CH340) 3, ALIENTEK 2.8/3.5/4.3 inch LCD module (only supporting MCU screen) 4. Keyboard KEY0 (PC5)/KEY1 (PA15)/KEY_UP (PA0, also known as WK_UP) Experimental phenomena: The timer AutoReloadTimer_Handle can be turned on by keying KEY_UP. This is The periodic timer will run continuously once it is turned on until KEY1 is pressed to turn it off. Press KEY0 You can turn on the timer OneShotTimer_Handle, which is a single timer and only runs once. The run cycle will stop after that unless KEY0 is pressed to turn it on again.)
    2020-06-24 05:00:01下载
    积分:1
  • 12864testdisplay
    说明:  万能的12864显示驱动程序,稍加修改可应用于多种单片机(Almighty 12864 display driver, slightly modified can be used in a variety of SCM)
    2010-04-08 12:14:42下载
    积分:1
  • tongxin
    智能小车使用遥控控制的源代码,本代码可以作为进一步研究的参考(Smart car using the remote control of the source code, the code can be used as reference for further research)
    2013-10-25 15:14:21下载
    积分:1
  • ex05_asm_IOA_IN_IOB_OUT
    这是用asm编写的IOA口使用程序,是用16位的凌阳单片机汇编(This is asm2 prepared by the IOA I use the program is the use of Sunplus 16 MCU Series)
    2006-09-22 17:16:24下载
    积分:1
  • 8串口控制led
    zigbee cc2530 基础实验之八 串口控制led灯编程实验(ZigBee CC2530 basic experiment eight serial port control LED lamp programming experiment)
    2017-11-22 11:17:01下载
    积分:1
  • STM32增量编码器例程
    说明:  通过增量式编码器A,B,Z项实现对编码值的输出,速度输出和方向判断(The output, speed output and direction judgment of coded value are realized by incremental encoder..)
    2019-07-04 11:18:16下载
    积分:1
  • Dcm
    诊断通信系统 AUTOSAR 诊断系统下位机与外界的通信由 DCM 负责。DCM 模块的主要功能在于保证诊断的数 据流管理诊断状态, 尤其是诊断会话和安全状态.(The communication between the lower computer and the outside of the diagnostic communication system AUTOSAR diagnosis system is responsible for the DCM. The main function of the DCM module is to ensure that diagnostic data flows are managed and diagnosed, especially in the diagnosis of sessions and security states.)
    2018-03-11 20:23:44下载
    积分:1
  • 696518资源总数
  • 104347会员总数
  • 12今日下载