登录
首页 » matlab » 标准响应面法

标准响应面法

于 2019-08-21 发布
0 114
下载积分: 1 下载次数: 20

代码说明:

说明:  标准响应面代理模型可用于可靠性分析,优化设计等结构分析领域(Standard Response Surface Agent Model can be used in structural analysis fields such as reliability analysis, optimization design, etc.)

文件列表:

响应面算法(标准).txt, 1116 , 2017-10-05
RSM.m, 1117 , 2018-06-06

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • almanak
    almanak reader polar plot
    2010-11-25 07:46:55下载
    积分:1
  • reliabilitycal
    matlab环境下求可靠性的程序,主要部分为求取最小路,采用容斥公式求可靠度
    2010-05-13 21:41:18下载
    积分:1
  • trial4
    求出laguerre滤波器的分子分母系数,绘出其幅频响应图并与FIR滤波器作比较。该程序为19阶Laguerre低通滤波器和22阶带通滤波器(obtained laguerre filter coefficient of molecular denominator, chart its amplitude frequency response plans with the FIR filter for comparison. The procedure for the 19-Laguerre low-pass filter and 22 band pass filter)
    2006-12-14 11:20:34下载
    积分:1
  • ofdmsnr
    ofdm snr is designed for signals
    2013-07-30 21:45:15下载
    积分:1
  • Active-Inductor-Current-Balancing
    Active Inductor current balancing for multiphase buck-boost converter
    2012-10-30 20:42:39下载
    积分:1
  • 2ddp_node
    2ddp dynamic mesh for fluent udf
    2013-12-12 15:26:08下载
    积分:1
  • binverter
    INVERTER MODEL IN SIMULINK
    2013-03-30 02:57:56下载
    积分:1
  • satellite-system
    基于数字地球的车载卫星导航定位的设计与实现(Digital Earth s satellite navigation and positioning the vehicle design and implementation)
    2013-12-01 10:06:50下载
    积分:1
  • Boost_Converter
    说明:  升压转换器是一种DC / DC电源转换器,可将电压从其输入(源)升至其输出(负载)。在连续导通模式下(流经电感的电流永远不会降为零),升压转换器的理论传递函数为: 占空比在哪里0.5 在此示例中,转换器从250 V电源馈送RC负载,并且PWM频率设置为31 kHz。 模拟 运行仿真并观察示波器上的波形。确认负载电压(Vout)的平均值非常接近理论值:Vout = 250 /(1- 0.5)= 500V。(A boost converter is a DC/DC power converter which steps up voltage from its input (source) to its output (load). In continuous conduction mode (current through the inductor never falls to zero), the theoretical transfer function of the boost converter is: where is the duty cycle.0.5 In this example, the converter is feeding an RC load from a 250 V source and the PWM frequency is set to 31 kHz. Simulation Run the simulation and observe waveforms on Scope. Verify that the mean value of the load voltage (Vout) is very close to the theoretical value of: Vout = 250 / (1 - 0.5) = 500 V.)
    2020-03-22 20:41:56下载
    积分:1
  • Matlab3
    关于MATLAB的一个很好的PPT。讲的是符号运算。对于初学者很好。页面也很漂亮。(MATLAB on a good PPT. Talking about the symbolic operation. Good for beginners. Page is also very beautiful.)
    2009-07-13 18:42:21下载
    积分:1
  • 696518资源总数
  • 104384会员总数
  • 26今日下载