-
zigbee与stm32通信例子
程序1：stm32程序串口2接收串口1发送程序 ，改自扩展实验11 ATK-HC05蓝牙串口模块实验程序。
程序2：zigbee串口通讯-发送字符串。
连接方式：cc2530的P02连接stm32的PA2，P03连接stm32的PA3
程序2串口一直发送“hello zigbee”字符串 mini版stm32程序1串口2接收后转发串口1原样输出。(Program 1:stm32 program serial port 2 receive serial 1 send program, change from expansion experiment 11 ATK-HC05 Bluetooth serial module experiment program.
Program 2:zigbee serial communication - send string.
Connection mode: CC2530 of P02 connection, STM32 of PA2, P03 connection of STM32 of PA3
Program 2 serial port has been sent "Hello ZigBee" string mini version of STM32 program 1 Serial 2 receive after forwarding the serial port 1, the original output.)
- 2020-11-10 16:29:46下载
- 积分：1
-
FATFS 动态曲线
stm32LCD液晶显示屏动态曲线的实时显示DMA(Embedded Microcontroller dynamic curve)
- 2018-06-27 14:55:45下载
- 积分：1
-
Ali-adapting-software-MOD
Ali adapting software - Ali przystosowywanie softów (MOD) Programs
- 2013-09-19 16:34:56下载
- 积分：1
-
智能温度控制器
当温控开关打开时，若测得环境温度大于设定温度，则继电器吸合
启动电机工作；若测得环境温度小于设定温度，则继电器释放，
电机停止工作；(When the temperature control switch is turned on, if the measured ambient temperature is higher than the set temperature, the relay will suck in.
Start the motor; if the measured ambient temperature is less than the set temperature, the relay will be released.
The motor stopped working.)
- 2019-03-29 11:44:31下载
- 积分：1
-
XJCG12864 驱动常用的读写程序
XJCG12864 驱动ic是UC1705X, 常用的读写程序(XJCG12864 driver IC is UC1705X, commonly used read and write programs)
- 2020-06-16 02:40:02下载
- 积分：1
-
StallingsAES
AES,The AES Cipher,Key Terms, Review Questions, and Problems,S-AES Structure,Appendix 5A Polynomials With Coefficients In GF(28)
- 2010-06-19 04:27:35下载
- 积分：1
-
mppt_stm32
基于stm32的太阳能mppt控制程序，adc采集，oled显示(Stm32 based solar mppt control program, adc acquisition, oled display)
- 2021-03-17 10:09:20下载
- 积分：1
-
BC7281A中断方式代码
可驱动8/16位数码管显示或64/128只独立LED 的芯片BC72811A中断编程。BC7281A只占用单片机3个I/O口(can drive 8/16 Digital Display or 64/128 only independent LED chip BC72811A interrupted programming. BC7281A only occupies three microcontroller I/O port)
- 2005-07-11 18:45:35下载
- 积分：1
-
a
说明： 设计一个VI来测量温度（保留2位小数），每隔0.25秒测一次，共测定10秒。在数据采集过程中，VI将在波形Chart上实时地显示测量结果。采集过程结束后，在Graph上画出温度数据曲线,并且把测量的温度值以文件的形式存盘，
使用记事本打开文件检查结果是否正确。
存盘格式为：
点数 时间(S) 温度值(度)
1 0.25 78.56
2 0.50 85.32(Design a VI to measure the temperature (keep two decimal places), measured once every 0.25 seconds, 10 seconds were measured. In the data collection process, VI will display the measurement results in real time on the waveform Chart. After the acquisition process, the temperature data in the Graph draw curves, and the temperature measured in the form of document archiving,
Use Notepad to open the file to check the result is correct.
Save format:
Points Time (S) temperature (degrees)
  1 0.25 78.56
  2 0.50 85.32)
- 2014-04-16 12:24:25下载
- 积分：1
-
txsend
本资源提供了采用PIC单片机实现单线通讯的源程序，通过调试(Resources to provide the PIC MCU using one-way communication source, through the commissioning)
- 2009-04-15 21:18:06下载
- 积分：1
