-
POCS7
针对超分辨图像图像的pocs算法源代码，对多帧序列的毫米波图像进行处理(Image super-resolution images for pocs algorithm source code, on the millimeter wave multi-frame image sequence processing)
- 2011-05-18 12:17:57下载
- 积分：1
-
jiaozheng1
一个单位负反馈系统的滞后超前频域法校正，可直接在matlab中打开和运行(A unit negative feedback system lag correction ahead frequency domain method can directly open and run in matlab)
- 2013-10-29 20:34:59下载
- 积分：1
-
Matlab
digital processing in matlab
- 2013-10-30 09:40:10下载
- 积分：1
-
Matlab-tool
说明： matlab工具箱包含大部分的数学函数，非常适合学习(Matlab toolbox contains most of the mathematical function, very suitable for learning)
- 2012-04-24 21:41:21下载
- 积分：1
-
VECTEURS
programme vecteur mathématique
- 2014-12-04 19:21:09下载
- 积分：1
-
The-cuckoo-algorithm
布谷鸟算法研究，并附matlab的实例。(The cuckoo algorithm on MATLAB)
- 2015-11-02 11:46:12下载
- 积分：1
-
music (2)
信号相干时MUSIC算法与改进MUSIC的比较仿真源代码(Signal coherence between MUSIC algorithm and improved MUSIC simulation source code)
- 2018-05-28 01:59:17下载
- 积分：1
-
项目4
说明： 任务：设计一个4×2.5Gbit/s 长距离光纤传输系统，并利用OptiSystem 仿真验证。
要求：
1．采用波分复用技术，波长设置以100GHz 为间隔，频率分别为193.1THz、193.2THz、193.3THz、193.4THz，每个波长传输速率为2.5Gbit/s（NRZ），传输距离为300km。采用常规光纤，光纤损耗系数为0.25dB/km。
2．单通道光发送机最大输出功率为0dBm，光接收机的接收光功率不低于－26dBm，过载点为－10dBm。
3．可以采用EDFA 作为线路放大器，其中EDFA 的输入功率限制在－18～2dBm，最大输出功率20dBm，增益范围为13～25dB，噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify.
Requirement:
1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km.
2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm.
3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
- 2019-05-13 09:39:41下载
- 积分：1
-
annealing
简单实用的模拟退火算法（SB/SW） 提供一个对理解模拟退火算法很好的程序示例(Simple and practical simulated annealing algorithm (SB/SW))
- 2009-03-16 09:48:52下载
- 积分：1
-
The_Finite_Element_Method_Using_Matlab_2nd_Ed_4AH
finite element method use machanical engineer to solve the problem about finite
- 2009-12-16 09:17:27下载
- 积分：1
