-
拉力传感器电机控制
数据采集卡采集拉力值，与预先设定的拉力值进行比较，然后PID运算，控制相应的PWM占空比输出，最终控制电机的速度(The data acquisition card collects the pull value and compares it with the pre-set pull value. Then the PID arithmetic is used to control the output of the corresponding PWM duty cycle, and finally the speed of the motor is controlled.)
- 2020-06-17 02:00:01下载
- 积分：1
-
volt-ampere-characteristic-t
元件伏安特性测量。包括磁滞回线、二极管测试、三极管、三极管（随机数）(Component volt-ampere characteristic measurement. Including the hysteresis loop, diode test, transistor, transistor (random number))
- 2013-12-29 16:40:43下载
- 积分：1
-
CCD Driver
CCD相机控制程序，用labview 驱动线阵CCD，可以设置采样时间/频率/曝光度等参数。(CCD driver,drive CCD camra with labview, with controlling of sample time parameter.)
- 2019-04-06 02:59:11下载
- 积分：1
-
English-conversion
界面中英文转换，简单有效的文件和条理，仅供参考(Interface in English conversion, a simple and effective documents and structured for reference only)
- 2013-03-10 12:42:17下载
- 积分：1
-
软件定时
对于无法实现硬件定时的数据卡来说，这个vi提供了软件定时的功能(For data cards that cannot achieve hardware timing, this VI provides software timing capabilities)
- 2020-06-17 02:00:01下载
- 积分：1
-
Synchronous-acquisition
利用labview完成电压信号和脉冲信号同步采集(Synchronous acquisition of voltage and pulse using LabVIEW)
- 2017-04-25 18:11:40下载
- 积分：1
-
LABVIEW___Select the sort formula node
一随机数组，按从小到大排列，基于公式节点做的(A random number group is arranged from the smallest to the largest, based on the formula node.)
- 2018-03-29 15:40:26下载
- 积分：1
-
信号频谱分析
用LABVIEW实现信号的仿真，并对其进行频谱分析。(The simulation of the signal is realized with LABVIEW, and the spectrum analysis is carried out.)
- 2017-11-29 21:58:37下载
- 积分：1
-
NI-DAQmx-read
自从NI-DAQmx 发布以来，NI 数据采集(DAQ)用户就充分利用了它的许多特性，这些特性是为节省开发
时间和提高数据采集应用程序的性能而设计的。
一个能节省相当大一部分开发时间的特性是NI-DAQmx 应用程序编程接口（API），它在各种设备功能
和设备系列中都是相同的。这就意味着一个多功能设备的所有功能可由同样的函数集编程得到（模拟输
入、模拟输出、数字I/O 和计数器）。而且，一个数字I/O 设备和一个模拟输出设备都可使用相同的函
数集编程得到。在LabVIEW 中，由于多态机制，因而这是可以实现的。一个多态的VI 接受各种数据类
型以用于一个或多个输入和/或输出终端。NI-DAQmx API 在它所支持的所有编程环境中也是保持一致
的。您仅仅需要学会如何使用一个单一的函数集就可以在多种编程环境中对大部分NI 数据硬件进行编
程。 (Since the release of NI-DAQmx, NI data acquisition (DAQ) users take full advantage of its many features, these characteristics are developed in order to save
Time and designed to improve the performance of data acquisition applications.
A large part of the development time-saving features a NI-DAQmx application programming interface (API), which function in a variety of equipment
And equipment series are the same. This means that all the functions of a multifunction device by the same set of functions programming (analog input
Into, analog output, digital I/O and counter). Moreover, a digital I/O device, and an analog output device can use the same letter
Number set programming to get. LabVIEW, polymorphism, and thus can achieve. A polymorphic VI to accept a variety of data classes
Type for one or more input and/or output terminals. NI-DAQmx API it supports all programming environment is consistent
s. You just need to learn how to use a single set of functions can)
- 2012-11-24 23:54:29下载
- 积分：1
-
clock
时钟美化控件，用于实现LabVIEW界面编程中对窗体的美化(The clock to beautify control for LabVIEW programming interface in the form of beautification)
- 2013-03-25 10:37:51下载
- 积分：1
