登录
首页 » Windows_Unix » ESP_8266 测试板原理图和PCB源文件

ESP_8266 测试板原理图和PCB源文件

于 2019-03-09 发布
0 121
下载积分: 1 下载次数: 8

代码说明:

说明:  ESP8266硬件参考设计文件,有硬件PCB原理图,三个文件。。。(ESP8266 file,PCBSCHPDF,for learning)

文件列表:

ESP8266_TESTER.pdf, 85721 , 2014-09-25
ESP_8266_DEMO_TESTER2.pcb, 488155 , 2014-09-16
ESP8266_TESTER.sch, 118004 , 2014-09-19

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Ultrasonic-1602
    基于MP430的超声波1602的产生及AD转换(MP430 s generation of ultrasound 1602 and AD converter)
    2012-05-11 10:06:29下载
    积分:1
  • serial-74LS165
    这是关于单片机各种应用接口的子程序还有驱动程序,还是用c语言写的,非常实用(on SCM applications Interface subroutine also driver, or a c languages, very practical!)
    2007-03-19 23:10:15下载
    积分:1
  • ymodem_mcu
    linux系统与单片机通过ymodem协议传送文件(linux system send a file to mcu form serial.)
    2016-06-08 15:59:10下载
    积分:1
  • 1.LED
    51单片机中的开发板上的LED跑马灯程序,很简单但是很实用适合新手/。(The program of LED horse-running lamp on the development board of 51 single-chip computer is very simple but practical for beginners/ novices.)
    2019-01-26 22:09:37下载
    积分:1
  • SHT30_Example实例教程
    SHT30温湿度传感器在stm32上使用的代码(Code for SHT30 Temperature and Humidity Sensor on stm32)
    2021-02-02 23:19:59下载
    积分:1
  • firmware
    说明:  这是我在学习红外遥控接收时写的代码,可能有一点用!(This is my infrared remote control receiver in learning to write code when there may be a point to use!)
    2008-11-16 22:46:38下载
    积分:1
  • bujindianji
    基于单片机MSP430的 步进电机控制 测距程序 (MSP430 microcontroller-based stepper motor control ranging program)
    2014-04-19 16:02:47下载
    积分:1
  • ZigBee-CC2430
    Zigbee 实战演练,CC2430学习手册。(Zigbee practical exercise, CC2430 study manual.)
    2013-08-28 09:31:34下载
    积分:1
  • Modbus_4
    第四章:以PC Based Controller设计Modbus通信程序 共6章(Chapter IV: A PC Based Controller Design Chapter 6 Modbus Communication)
    2010-09-15 13:40:21下载
    积分:1
  • 飞思卡尔
    飞思卡尔智能车控制代码,我们做的是变形三轮直立组,目前只有三轮状态下的运动控制代码,PID参数需要结合自己车模的结构参数做相应的调整,速度环和方向环均采用的是位置式pid算法。(Freescale Intelligent Vehicle Control Code, we do deformation three-wheel vertical group, currently only three-wheel motion control code, PID parameters need to be adjusted with the structural parameters of their own model, speed loop and direction loop are using position PID algorithm.)
    2020-06-21 13:00:01下载
    积分:1
  • 696522资源总数
  • 104042会员总数
  • 46今日下载