-
CAN-周立功
ZLG CAN通讯,Labview DEMO,包含二次开发动态链接库(ZLG CAN Communication, Labview DEMO, Including Secondary Development Dynamic Link Library)
- 2019-04-03 16:35:04下载
- 积分:1
-
H-Bridge & Motor demo
基于labview的电机控制程序,亲测能够使用(Motor control program based on LabVIEW)
- 2018-11-16 20:46:15下载
- 积分:1
-
basic_gpib_write_and_read
利用VISA去控制GPIB串口通信,最终实现与频谱仪,电源,示波器等相互之间通信(VISA to control GPIB serial communication, and ultimately with the spectrum analyzer, power supplies, oscilloscopes, and other mutual communication between)
- 2012-07-18 20:36:26下载
- 积分:1
-
CCD Driver
CCD相机控制程序,用labview 驱动线阵CCD,可以设置采样时间/频率/曝光度等参数。(CCD driver,drive CCD camra with labview, with controlling of sample time parameter.)
- 2019-04-06 02:59:11下载
- 积分:1
-
LV2012_FreeCOM
在labview环境下编写的一个串口助手,可以读取数据,保存数据,截屏的功能,功能强大,适合初学者(A LabVIEW environment in the preparation of serial assistant, you can read the data, save data, screenshot function, powerful, suitable for beginners)
- 2014-06-06 15:47:01下载
- 积分:1
-
2-10
华氏度转换为摄氏度,代码短小,可靠性高,转化方便,适合做课后练习(Convert Fahrenheit to Celsius, the code short, high reliability, easy transformation, suitable for after-school practice)
- 2013-12-10 14:11:34下载
- 积分:1
-
Motioncontrolinfrastructureinlabview
几乎所有的自动设施一一从工业机器到医疗设备一一其组件如何移动都必须按照控制方式执行。移动负载最常见的方法就是使用一些电机元件如电动机。我们来学习如何控制基于电动机的系统,并探究NI公司所提供的各种不同的机器控制解决方案。(Almost all auto facilities one by one how to move from industrial machinery to medical equipment eleven components must be performed according to the control mode . Moving load is the most common method is to use some of the motor components such as motors. Let s learn how to control the motor- based systems)
- 2012-10-10 23:19:34下载
- 积分:1
-
usb6251
关于如何使用NI公司USB-6251数据采集卡的参考文献(Companies on how to use NI USB-6251 data acquisition card References)
- 2021-03-08 16:59:28下载
- 积分:1
-
110230
停车场车库管理系统设计。大学毕业设计!课程设计用!(Design parking garage management system. University Graduation! Curriculum design! )
- 2014-06-28 11:04:51下载
- 积分:1
-
hanshuxinhaofashengqi
1.采用Labview设计一虚拟函数信号发生器, 通过数据采集卡输出波形信号,调节信号的相关参数,可观察示波器上波形的变化情况。
⑴ 以NI MyDAQ数据采集卡作为输出接口;
⑵ 数据采集卡输出多种信号,至少完成三种波形:正弦波、三角波、方波(可调占空比)的输出,同时前面板上显示各输出波形;
⑶ 频率、幅值、初相位、直流偏移量和方波的占空比(0~100 )等参数可以通过前面板控件调节。
⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes.
⑴ with NI MyDAQ data acquisition card as output interface
⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel
⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust.
⑷ output waveform can be displayed on the front panel.)
- 2015-04-25 18:26:52下载
- 积分:1