-
line
线阵天线方向图的画法 可改参量 实现不同参量下的方向图(The Drawing of Line Antenna Pattern)
- 2017-09-26 15:53:31下载
- 积分:1
-
SPHYSICSgen2D
SPH方法计算二维溃坝问题的源程序,个人觉得还可以(Two-dimensional dam break problem SPH method the source, individuals felt that I could)
- 2011-05-30 11:26:57下载
- 积分:1
-
5CFDprogram
压缩包中包含五个CFD基础程序,其中MacCormack1DSolveRiemann.for是一维欧拉方程求解(黎曼问题),UpwindTVD_1D.for是一维可压粘性N-S方程求解,MAC-Chorin2D.for是利用MAC算法和Chorin压力迭代解法求解
二维不可压缩黏性平板间Poisuille流动问题,Lax-Webdroff2D.for是利用Lax-Webdroff差分格式求解二维平面激波反射问题,fvm_upwind_MAC_couette.for是以一阶迎风型离散格式和Chorin压力迭代求解couette二维流动问题。(CFD compression package contains five basic program, which is an Euler equation solving MacCormack1DSolveRiemann.for (Riemann problem), UpwindTVD_1D.for is one-dimensional compressible viscous NS equation solving, MAC-Chorin2D.for is the use of algorithms and MAC Chorin pressure iterative solution for solving the two-dimensional incompressible flow problems between viscous flat Poisuille, Lax-Webdroff2D.for using Lax-Webdroff difference scheme for solving the two-dimensional plane shock wave reflection problem, fvm_upwind_MAC_couette.for based on first order upwind scheme and Discrete Chorin pressure couette iterative solution of two-dimensional flows.)
- 2015-01-16 19:01:12下载
- 积分:1
-
BladedDLLInterface
This source file contains example PitchCntrl(), UserHSSBr(),
! UserVSCont(), and UserYawCont() routines that are used to interface
! FAST with a master controller implemented as a dynamic-link-library
! (DLL) in the style of Garrad Hassan s Bladed wind turbine software
! package. All four routines call routine BladedDLLInterface(), which
! contains a call to the Bladed-style DLL that evaluates as DISCON().
! Routine BladedDLLInterface() USEs a MODULE named
! BladedDLLParameters(), which stores values of PARAMETER constants
! used in the interface.
- 2013-09-05 03:49:38下载
- 积分:1
-
1D_introduction-FDTD
很详细的一维FDTD介绍,以及MATLAB程序说明(Very detailed one-dimensional FDTD presentation and description of the MATLAB program)
- 2021-03-26 23:29:12下载
- 积分:1
-
revealing-
使用labview2009开发平台,实现对机械信号频谱泄露的功能。(Use labview2009 development platforms for the mechanical function of the signal spectrum leakage.)
- 2011-09-02 11:21:20下载
- 积分:1
-
fftbianhuan
test1.txt 第一列为时间t,0.001s为步长;第二列为系统的输入信号;第三列为系统的输出信号。
signal_analyzer.m首先将test1.txt 的数据读入workspace,然后进行FFT,分析出两信号的频率,输出对于输入的幅值衰减(db),输出对输入的相位差。(test1.txt the first time as t, 0.001s for the step the second as the system input signal the third as the system output signal. signal_analyzer.m first test1.txt data read workspace, and then proceed to FFT, analysis of the two signals in the frequency, the output for input amplitude attenuation (db), the output of the input phase difference.)
- 2008-12-13 02:19:50下载
- 积分:1
-
wg12154615345
说明: matlab改进的网格算法,work3为主程序(Matlab improve grid algorithm, based procedures work3)
- 2006-01-06 14:55:18下载
- 积分:1
-
MYFEM
有限元求解柏松方程。本文采用FORTRAN语言编制程序。程序中大部分变量采用有名公共区存储方式存储,这样可以减少内存占用量。
IFG:生成有限元网格信息,即元素节点局部编码与总体编码对照表,节点实际坐标,边界节点编码与边界点上的已知值
GKD:生成总刚一维存储对角元的地址,计算总刚一维存储长度
FIXP:设置已知节点函数值
GK(NI,NJ,ADJ,AIJ):单元刚度矩阵计算
GF(NI,N,M,LE,YI,FE):单元列阵的计算
AK(I,J,AIJ):总刚度矩阵元素迭加
QEB:总刚度矩阵和总列阵合成
BDE:边界条件处理
SOLGS:Gauss-Seidel迭代法求解方程组
UDIFF(NI,NFLAG,UDIF,LE,ADJ):标准元素内形状函数导数计算
DIFF:节点上 , 加权平均
(In this program, FEM was used to solve the possion equation. It is implemented through FORTRAN)
- 2009-05-22 17:22:56下载
- 积分:1
-
neff_m72
改程序是计算出金属表面等离子体直波导的有效折射率随波长和传输长度随波的两色散曲线,另外给定Drude-Lorentzia模型参数给定后,还可以求解介电常数以及画出相应实部和虚部的曲线(This programer is used to calculate Ag relative dielectric constant
accroding to the Drude-Lorentzia and sovle the transcendental equation
for even illumination. At the same time,it can draw the diagram of
relationship between the dispersion curve and the Transmission with
the length. )
- 2012-10-18 20:33:53下载
- 积分:1