-
H infinite transfer alignment
从实际应用的角度出发，提出利用跟踪微分滤波器抑制机冀挠曲变形产生的影响，通过杆臂效应补偿消
除干扰加速度，用延时补偿算法减少由数据传输延迟造成的量测信息误差。在此基础之上，采用“速度+姿态”
匹配方案，研究了基于H_滤波估计的快速传递对准方法.大量数值仿真、静态试验、动态跑车试验表明，这
些方法有收敛速度较快、精度较高的特点，并t,有较强的抗干扰能力。试验也验证了传递对准方法的有效、可
行，能满足控制系统对导航信息的精度要求.
()
- 2008-04-02 19:08:00下载
- 积分：1
-
CDMAQ2358C
CDMA码分多址技术。包括指令编写说明和Q2358C型号CDMA的说明书(CDMA Code Division Multiple Access technology. Including the preparation of instructions and instruction manuals Q2358C CDMA models)
- 2010-05-17 22:07:50下载
- 积分：1
-
OQAM
ofdm/oqam系统源码 4qam调制下oqam与cp——ofdm比较(ofdm/oqam system source code modulation oqam 4qam with cp- ofdm Compare)
- 2020-07-02 17:40:02下载
- 积分：1
-
cpofdm
说明： cpofdm信道模型仿真，通过仿真得到cpofdm信道模型的复杂度和在各种信噪比下的误码率(Through the simulation of cpofdm channel model, the complexity of cpofdm channel model and the bit error rate under various SNR are obtained)
- 2021-04-15 10:08:55下载
- 积分：1
-
code_e
matlab编的信号符号速率估计的程序，比较容易的(matlab compiled the signal symbol rate estimation procedures, relatively easy)
- 2009-09-16 09:27:44下载
- 积分：1
-
phone_com
一个基于串口的手机短信发送/接收程序；Demo很简单，是以异步方式读写串口的；在对话框初始化中修改串口的配置参数正确后，能100％的正常发送/接收短信。
(A message based on the serial port of the mobile phone to send/receive process Demo is very simple, based on asynchronous serial reading and writing in the dialog box to initialize the serial port to modify configuration parameters correct to 100 of the normal Send/receive message.)
- 2008-07-13 18:24:26下载
- 积分：1
-
4qam
4QAM(QPSK)的调制解调以及计算误码率，最后将结果输出至表格。适合新手参考(The modulation and demodulation of 4QAM (QPSK) and the calculation of bit error rate, and finally output the result to the form. Suitable for novice)
- 2018-06-23 17:04:29下载
- 积分：1
-
enet-at002_-en-p
EtherNet/IP Socket Interface(This publication describes the socket interface that you can use to program
MSG instructions to communicate between a Logix5000 controller via an
EtherNet/IP module and Ethernet devices that do not support the EtherNet/IP
application protocol, such as bar code scanners,RFID readers,or other standard
Ethernet devices.)
- 2018-06-30 16:01:49下载
- 积分：1
-
BER
这是一个matlab和optisystem联合调试用的误码率计算程序，里面的文件报过一个可以用optisystem7和optisystem13可以打开的OSD仿真图，还有一个MATLAB计算BER的程序。给出了如何设置系统的大纲。从OptiSystem的电信号输入到Matlab组件。当OptiSystem运行时，它将调用Matlab组件中的M文件，处理数据，然后将所得的电信号导出回OptiSystem。然后将输出信号连接到BER分析仪。经过我调试，文件齐全，放心下载(The attached image gives an outline of how the system should be setup. You should start with inputting the electrical signal from OptiSystem into a Matlab component. When OptiSystem runs, it will call the M-file in the Matlab component, process the data, and then export the resulting electrical signal back into OptiSystem.The output signal is then connected to the BER Analyzer.)
- 2021-03-18 15:39:20下载
- 积分：1
-
tcp_udp_web_tools-pyqt5-master
说明： 使用pyqt编写的界面程序，实现串口网络通信(The interface program written by pyqt is used to realize the serial port network communication)
- 2020-01-07 15:48:10下载
- 积分：1
|
联系客服（QQ：3324461878）
